Front grill on toyota solara

Sara, 1989 GMC Suburban front bumper removal. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How To Install Replace Bent Rusted Front Bumper 1989 99 Chevy GMC Pickup...
Grille Replacement 88 98 Chevy trucks
1989 Chevrolet R1500 Suburban Parts NationalGMParts com

Remove wheels. Remove fender liners front. Remove three nuts per side from inside fender wells. Remove fog lamp grilles. Remove vertical bolt just inside grilles--pointing up. Remove two screws per side under hood near front of fender. Put milk crate under front bumper. Remove belly pan first. Slide bumper forward onto milk crate, disconnect headlight washer line at quick disconnect if so equipped. Disconnect fog light connectors. Remove bumper.

This video should help you. The bumper should not have to be removed.
http://www.youtube.com/watch?v=8ap1-CzG5Hc

I changed my 2001 Toyota Highlander headlights recently. First, remove the grille. There is one screw in the center which will require a loonng Phillips screwdriver to reach it, down behind the grille, right in the center. Then remove the four plastic clips at the top by prying them up with a small flathead screwdriver. The bottom just pulls forward. Important: Now go to each side of the car, and in front of each fender well, there is one clip that holds the bumper cover on. Pull the top corner of the bumper cover toward you to release the clips, one on each side, at the top corner, along the front of each fender well where the bumper cover meets the fender. The bumper cover can now be loosened along the top without entirely removing it. It just pulls forward. Inspect the underside of the bumper cover for broken clips and replace as necessary. Now remove the two bolts that hold down each headlight at the top. Disconnect the wiring and bulbs and wiggle the old headlights out. Install the new ones and reverse the process. If your AC isn't blowing cold, check the condenser for leaks before you reinstall the grille. A new aftermarket condenser/filter dryer is easy to install by removing the battery and tilting the radiator back to get the condenser out. A replacement only costs $75 and can be swapped out in one half hour with a few metric sockets. Then you will need to recharge the AC system with R-134a, which is easy. Just buy a R-134a kit with hose at Autozone and follow the directions. $50 Replacement fog lights are only $52/pair for aftermarket. You may consider replacing those as well. They have a strange installation with clips and you will need to pry/bop them forward, not remove them from the back. They are aggravating to replace but not technically difficult.

I have written up all the steps on how to remove the bumper of a 2004-2007 Toyota Sienna on my step-by-step tutorial on how to replace the radiator: John Fixes Stuff How to Replace the Radiator on 2004 2007 Toyota Sienna

start removing the grill and bolts holding the bumper in the side of the grille or holding the grille then loosen the fender liner were it meets the bumper and at the top edge of the bumper were it meets the fender they have a 10mm. bolt holding the bumper and voila bumper is off really easy....

yes , two underneath headlamp behind bumper you will need to remove front bumper to access

Strut tops are a common failure on the 97-01 era Camry/Solaras.

They will make a hollow rattle sound whenever you hit bumps or uneven pavement.

They can be replaced one at a time, and do not require strut replacement if your old struts are still in good shape.
Replacement does require a strut compressor and an alignment afterwards, placing it outside the scope of most do-it-yourselfers.

It is labeled "suspension support" in the following diagram. The bearing below it is typically replaced at the same time.

sorry to tell you that but you must take the bumper off and its pretty easy there are retainers up top remove them remove the bottom of the bumper ones and they may have bolts now for the last part its 100 mm at the fender edge and bumper just slide off and then you can take and change the grille

nono... go in through the engine. Pop the hood and you can do it without detaching anything but the old fog lamp.