Question about Cars & Trucks

Open Question

Jeep cj7 heater control cable instalation diagram

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Richard Scordino

  • 6982 Answers

SOURCE: vacuum diagram for 1980 cj7 jeep 2.5 motor

You can use any vacuum port on the manifold for that. If you want to mess with it a bit, if you have an open port on the carb that is above the throttle plate, you can use that and see if performance is better. Some engines like it and some don't, but it's not like you have to take the engine apart to try it!!

Posted on Oct 08, 2009

Ad

Anonymous

  • 97 Answers

SOURCE: 1984 Jeep CJ7 heater core leaking

  1. Disconnect battery ground cable and drain cooling system.
  2. Disconnect heater core hoses.
  3. Disconnect damper door control cables.
  4. Disconnect blower motor electrical connector.
  5. Disconnect water drain hose and defroster hose.
  6. Remove nuts retaining heater housing assembly to instrument panel. Remove heater housing assembly by tilting heater downward to disengage it from air inlet duct and pulling toward rear of vehicle.
  7. Remove heater core from heater housing.
  8. Reverse procedure to install.

Posted on Nov 17, 2009

D11RCD

  • 65 Answers

SOURCE: replacing front shackle 1983 jeep cj7

Shackles are pretty straight forward. Remove the existing bolts, change the shackles and reverse the procedure to install. Good idea to change the bushings while you're in there if they are at all questionable. It's best to do this with the CJ in the air, supported on the frame and use a floor jack under the axle to lift/lower the spring in/out of the shackle, one side at a time.

Posted on Nov 19, 2009

Testimonial: "But what if I am doing this in my garage without a lift?"

nzirbel

  • 47 Answers

SOURCE: engine compartment wiring diagram for a 88 cj7

The last Cj-7 was built in 1986. And they didn't come factory with a V-8 so you have a conversion of some type. Most factory wiring diagrams aren't going to help much. Sorry

Posted on Jan 26, 2010

skerritt

  • 1 Answer

SOURCE: I need a diagram of the rear brake system on a 79

Hi Jules, T. Skerritt here! Did you get your brakes figured out? I have a timing problem... Can you help?

Posted on Jul 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can i find free wire diagrams


free, for free google all day... join a real jeep forum and beg>?
sure
if time is more important.

alldata.com

log in and read.
or
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

Aug 08, 2014 | 1984 Jeep CJ7

1 Answer

No heat in 1983 jeep cj7


Yes the thermostat so stuck open not allowing the motor to properly warm up or it can be the climate control went bad

Mar 23, 2014 | 1983 Jeep CJ7

1 Answer

All lights work on my 83 cj7 except my dash lights


You either have the headlight dimmer control turned off or the dimmer control rheostat is defective

Aug 22, 2012 | 1983 Jeep CJ7

1 Answer

How to install heater core if 1985 cj 7 jeep with 151 cubic inch


If it is necessary to remove the heater assembly, the cooling system must be drained before removing the heater core.
When a heater core leaks, a new heater core is installed or the old one repaired.
Heater Housing
  • The heater housing is usually under the dash and must be removed to gain access to the heater core.
  • Procedures for replacing the heater core vary with the year, make, and model of car. It threfore necessary to consult the manufacturer's repair manuals for the proper procedure for replacement.
f74-01.gif The heater housing is disassembled to get to the heater core. Heater Core
  • Remove the access panels(s) or the split heater/air conditioning case to gain acess to the heater core.
  • Remove the heater coolant hoses.
  • Remove the cable and/or vacuum control lines (if equipped).
  • Remove the heater core securing brackets and/or clamps.
  • Lift the core from the case. Do not use force. Take care not to damage the fins of the heater core when removing.
  • To reinstall the heater core, reverse the removal steps.
When the heater core leaks and must be repaired or replaced, it is a very difficult and time-consuming job primarily because of the core's location deep within the firewall of the car. For this reason always leak test a replacement heater core before installation.

Jan 06, 2011 | 1984 Jeep CJ7

1 Answer

Jeep cj7 stock 4.2 fuel injected or carborated


It should be an electronically controlled carburetor.

Apr 02, 2010 | 1986 Jeep CJ7

1 Answer

Engine compartment wiring diagram for a 88 cj7 jeep v8


The last Cj-7 was built in 1986. And they didn't come factory with a V-8 so you have a conversion of some type. Most factory wiring diagrams aren't going to help much. Sorry

Dec 08, 2009 | 1986 Jeep CJ7

1 Answer

1984 Jeep CJ7 heater core leaking. '93 inline 6 motor. Wrangler dash. How to I remove the core?


  1. Disconnect battery ground cable and drain cooling system.
  2. Disconnect heater core hoses.
  3. Disconnect damper door control cables.
  4. Disconnect blower motor electrical connector.
  5. Disconnect water drain hose and defroster hose.
  6. Remove nuts retaining heater housing assembly to instrument panel. Remove heater housing assembly by tilting heater downward to disengage it from air inlet duct and pulling toward rear of vehicle.
  7. Remove heater core from heater housing.
  8. Reverse procedure to install.

Nov 17, 2009 | 1984 Jeep CJ7

1 Answer

Need to know how to replace a water pump on 81 cj7


This is for an 82 Inline 6 Aldata doesnt go back that far, if you need further info Hit Me Back

  1. Disconnect battery ground cable.
  2. Drain cooling system.
  3. Disconnect radiator and heater hoses from water pump, Fig. 21.
  4. Remove drive belts.
  5. Remove fan shroud and fan.
  6. Remove water pump attaching bolts, then the water pump and gasket.
  7. Reverse procedure to install.

May 31, 2009 | 1984 Jeep CJ7

1 Answer

Fusebox diagram


You need a Chiltons or Haynes manual

Apr 19, 2009 | 1983 Jeep CJ7

1 Answer

Need Fuse Block Diagram for 84 CJ7


If I'm correct there a fusible link for the headlights.
Probably of the starter solonoid.

Oct 05, 2008 | 1984 Jeep CJ7

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

505 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

john h

Level 3 Expert

22486 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...