1994 Eagle Vision Logo
A
Anonymous Posted on Oct 24, 2011

I need a diagram of the 1994 eagle vision engine bay, or just the wiring for the windshield washer fluid pump. Power isn't provided to the pump and I need to find which wires need checking/replacing. Any help is appreciated, thanks.

1 Answer

Anonymous

Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Genius:

An expert who has answered 1,000 questions.

  • Master 1,016 Answers
  • Posted on Mar 22, 2012
Anonymous
Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Genius:

An expert who has answered 1,000 questions.

Joined: Apr 02, 2010
Answers
1016
Questions
0
Helped
413249
Points
3013

Hi,
This should help you out.

I need a diagram of the 1994 eagle vision engine - 3_22_2012_12_38_21_am.jpg
Let me know if you need more information.
Thanks
Jason

5 Related Answers

Anonymous

  • 5 Answers
  • Posted on Nov 27, 2008

SOURCE: Windshield washer fluid will not pump

the windshield washer pump might be bad. It should be located somewhere on the reservoir

Ad

Anonymous

  • 512 Answers
  • Posted on Dec 04, 2008

SOURCE: my eagle vision radio is not worrking i need the owners manual

check fuse 2 and 13 in the fuse block inside the car

Anonymous

  • 1 Answer
  • Posted on Jan 21, 2009

SOURCE: Windshield washer Pump doesn't run, but the pump checks out good

there is another small relay box just below the windshield washer reservoir about 11/2" wide x about 4" long the washer pump relay is in there



Anonymous

  • 205 Answers
  • Posted on Mar 22, 2009

SOURCE: Rear windshield washer motor works, but no fluid comes out

Rear washer may have it's own reservoir . Can you hear a pump humming when you activate the washer? Look in the under flooor compartment

Anonymous

  • 1 Answer
  • Posted on Jun 17, 2009

SOURCE: Windshield washer fluid pump quit. 2005 Jetta

I have a 2003 Jetta and the fuse box is between the dashboard and the drivers side door. There is a lid that covers it on the dashboard side. Inside there is a diagram/fuse card. The card has one top rectangular series of fuses numbered 8 through 23. Below is a square series numbered 24 through 44. The washer fuse is number 24 on the top left of the bottom square series. For me, I checked the fuse and it was good, therefore I am assuming that my pump is dead.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

2006 Malibu maxx front or back washer pumps will not work. pulled both pumps out and made sure both work. I have pulled all fuses, relays out replace them all. Both pumps work off Separate switches.

Replacing parts just to replace them wont fix a bad wire or part. Better to use a voltmeter and ohn meter to check if your getting power to the wires. You may have a bad connection or bad switch on the column for the pumps. Without checking the circuits it will behard to tell what it is thats wrong. Find a wiring diagram and trace the wires and components.
0helpful
1answer

I need a wiring diagram for 1995 eagle vision

you cant get a wiring diagram for the whole car ,that would be 100s of pages, so go to (images of wiring diagrams (year ,make ,model,motor size) and what section you need) like power window,head lights, ignition, fuel pump, got the idea.
0helpful
2answers

Where is the rear windshield fluid reservoir located on a 1994 Toyota Camry Station Wagon?

not 100% on this, but typically, you have to open the back hatch, and there will be a small rubber cap over the opening for the washer fluid located on or near the top of one of the taillight lenses on either side of the vehicle.


I’m happy to help further over the phone at https://www.6ya.com/expert/adrienne_b03fb46fc6334991

0helpful
1answer

I have a 2001 hyundai elantra and my fluid doesnt squirt out. do i look for a blown fuse or could it be the pump. i dont hear the pump so im thinking maybe that might be it but im not sure thanks for your...

Since you don't hear the pump motor running when the switch is turned on, the problem could be the switch itself, a blown fuse, bad wiring to or at the pump motor or the motor itself. Common problems with all windshield washer systems over time is the pump itself, but isn't ALWAYS the pump. Have the system properly diagnosed before you start spending money on parts you may not have to replace.
Go to www.hmaservice.com and register your vehicle by VIN #.. you'll then have access to wiring diagrams, shop manuals, service bulletins, illustrations and procedures, etc.

This should help
0helpful
1answer

What type of fluid do I use in a power stearing pump on a 1995 Eagle vision

You go to an autoparts store and buy a bottle of Power Steering Fluid.
2helpful
1answer

Mercury villager 1994 washer pump not working

the pump motor likely is bad. get a used washer fluid reservoir at a pick n pull yourself or at car-part.com. page with * is lowest cost.

Pump and Reservoir, Windshield Washer Removal
  1. Disconnect the battery ground cable (14301).
  2. Raise and support the vehicle.
  3. Remove the RH wheel (1007).
  4. Remove the RH front fender splash shield (16103). Refer to Section 01-02 for the removal procedure.
  5. Remove the windshield washer reservoir top bolt.

  6. Disconnect the windshield washer reservoir fluid level sensor electrical connector.
  7. Disconnect the rear window washer pump electrical connector from the rear window washer pump.
  8. Disconnect the windshield washer pump electrical connector from the windshield washer pump (17664).
  9. Place a suitable drain pan under the windshield washer reservoir (17618) and drain the washer fluid.
  10. NOTE: The rear window washer hose end is color-coded, matching the connector on the rear window washer pump. Match the colors to ensure proper installation.

    Disconnect the washer hoses from the windshield washer pump and the rear window washer pump on the windshield washer reservoir.

  11. Loosen the two windshield washer reservoir side bolts.
  12. Remove the windshield washer reservoir by sliding it out of the side slots.
  13. Remove the windshield washer pump.

    Installation
To install, reverse the removal procedure. Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).
0helpful
1answer

Windshield washer quit working

check fuses under dash and in enginge compartment/thenif the fuses are ok then its the pump itself that needs to be replaced/ Please rate my response thank you very much
26helpful
3answers

Windshield washer Pump doesn't run, but the pump checks out good

there is another small relay box just below the windshield washer reservoir about 11/2" wide x about 4" long the washer pump relay is in there



Not finding what you are looking for?

401 views

Ask a Question

Usually answered in minutes!

Top Eagle Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1212 Answers

Are you an Eagle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...