How to put on a crank sensor for a 2.4 engine of a 2001 oldsmobile alero?

How to start this 2001 Oldsmobile Alero - YouTube

? 2:00
https://www.youtube.com/watch?v=J1VRZ5cUYB8
Feb 15, 2013 - Uploaded by carexpertandy
How to start this 2001 Oldsmobile Alero ... to let me know my car still on if i dnt make the payment they turn the car off at the lot and it wont start.

No Start Due to Failed Passlock Sensor : Oldsmobile Alero ...

repairpal.com > Problems > Oldsmobile > Alero

Oldsmobile Alero No Start Due to Failed Passlock Sensor. This is a ... 2001 Oldsmobile Alero117,000Visitor .... 2004 olds alero wont start in park does in neutral.

2001 Oldsmobile Alero wont start? ' Yahoo Answers

https://answers.yahoo.com/question/index?qid...

Mar 15, 2011 - Alright guys, Last night I drove my Alero all over town with several friends. I wake up for work today, it wont crank! It has no recognition for the ... My 2001 Oldsmobile alero will not start. It will crank and has ...
Nov 27, 2013
HELP! I'M LATE FOR WORK, AND MY CAR WON'T START!!!?
Apr 6, 2011
Ran out of Gas 2001 Oldsmobile Alero won't start?
Dec 14, 2008
2001 Oldsmobile Alero Turns Over But Won't Start?
Dec 14, 2008
More results from answers.yahoo.com

2001 Oldsmobile Alero Won't Start - How To Fix It ' M

Oldsmobile Alero MAP Sensor - PartsGeek.com

www.partsgeek.com > ... > Oldsmobile MAP Sensor > Alero Parts

Oct 29, 2008 - 04 2004 Oldsmobile Alero GL MAP Sensor 3.4L V6 VIN: E Delphi · Click to Enlarge ... Vehicle, Engine. • 2002 (02) Oldsmobile Alero, 3.4L V6. 04 2004 Oldsmobile Alero MAP Sensor 2.2L 4 Cyl Standard Motor Products.

Part 1 -How to Test the MAP Sensor (GM 2.4L Quad 4)

troubleshootmyvehicle.com > GM > 2.4L

Jun 7, 2011 - GM 2.4L MAP Sensor Test with a Multimeter. ... 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002. Malibu 2.4L. 1997, 1998 ... Alero 2.4L. 1999 .

check the wires on the starter

It depends on which crank sensor you are wanting to replace. There are two of them. The 24X sensor is located behind the front crankshaft pully and the crank pully must be removed to change it. The 7X sensor is located in the engine block on the right bank (firewall side) near the rear of the engine. This one simply pulls out of the block after disconnecting the electrical connector and removing the single bolt that holds it.

The crank sensor is located in the front of the engine just above the oil filter.

p1227 Oldsmobile Injector 2 Control Circuit Shorted
p1245 Oldsmobile Intake Plenum Switchover Valve
p1275 Oldsmobile Accelerator Pedal Positioning (APP) Sensor 1 Circuit p0300 Oldsmobile Multiple Engine Misfire Detected p0172 Oldsmobile Fuel Trim System Rich (Bank 1)
sounds like bad injectors for one and computer needs relearned or replaced unfortuantly u gotta goto to the dealer have diagnostics ran

on the 3.4 liter engine, it's behind the harmonic balancer--you have to remove the crankshaft pulley/balancer to see it.

if you have the 2.4 liter, it's just above the oil filter:

I am assuming its not the service engine soon light it is probably the service vehicle soon light, There are 2 lights service vehicle soon upper left side, and service engine soon upper right side.

When all these come on at the same time it is the wheel bearing sensor. Usually the wheel bearing needs to be replaced which houses the sensor. A sure way to check is to press your sls button by your shifter and see if the light goes out, If it does not, u will need to have a wheel bearing put in.

the crank sensor is located beneath the intake between the starter and oil filter it has one small bolt in it remove the bolt and pull the sensor out and just stick the new one in put the bolt back in it and plug it up but make sure you disconnect the battery before you do anything that bolt is probably a 10mm or a 5/16 i hope this helps

ignition coil pack it intermitten.

also check the crank sensor and the main crank pulley, this is where the engine gets its firing orders from