Need head bolts tourqe sequence for a 89 tercel

Cylinder Head Bolts (First Pass all M11 Bolts in Sequence)
30 N?·m
22 lb ft
Cylinder Head Bolts (Second Pass all M11 Bolts in Sequence)
90 degrees
Cylinder Head Bolts (Final Pass all M11 Bolts in Sequence-Excluding the Medium Length Bolts at the Front and Rear of Each Cylinder Head)
90 degrees
Cylinder Head Bolts (Final Pass M11 Medium Length Bolts at the Front and Rear of Each Cylinder Head in Sequence)
50 degrees
Cylinder Head Bolts (M8 Inner Bolts in Sequence)
30 N?·m
22 lb ft
Intake Manifold Bolts (First Pass in Sequence)
5 N?·m
44 lb in
Intake Manifold Bolts (Final Pass in Sequence)
10 N?·m
89 lb in
Intake Manifold Wiring Harness Stud
10 N?·m
89 lb in

http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0900c1528008da66 Here's a link to your head torqe sequence.

Torque sequence ------------ front ' 10 6 2 3 7 ' of ' ' engine ' 9 5 1 4 8 ' ------------ Step 1: torque in sequence to 52-59 Ft/Lbs Step 2: torque in sequence to 70-76 Ft/Lbs Recheck final torque in sequence
Hope it helps you.

1. CAUTION
2. During the final tightening sequence, bolt No.11 will be tightened to a lower torque than the rest of the bolts. DO NOT over tighten bolt No.11.
3. 
   
5. Tighten all bolts in sequence (1 through 14) to 22 ft. lbs. (30 Nm).
6. Tighten all bolts in sequence (1 through 14) to 45 ft. lbs. (61 Nm).
7. Check all bolts to verify they are set to 45 ft. lbs. (61 Nm).
8. Tighten bolts in sequence:
9. Bolts 1 through 10 to 110 ft. lbs. (149 Nm).
10. Bolt 11 to 100 ft. lbs. (135 Nm).
11. Bolts 12 through 14 to 110 ft. lbs. (149 Nm).
12. Check all bolts in sequence to verify the correct torque.

A torque specification is how tight you must make the bolt by using a torque wrench which measures the tightness you apply to the bolt, ensure you are using new head bolts, a reliable torque wrench, clean the threads of the cylinder head (with tap) where head bolts screw into and when installing bolts ensure they are properly lubricated. And the sequence is the order in which you tighten each bolt.

Hello proskater442: My name is Roger and I will help you. The cylinder head torques in two steps. Make sure all bolts are good before attempting to torque them Inspect for any broken or deformed threads. Replace any that are damaged. I attached a picture of the torque specs. and tightening sequence. Should you need further help please just ask. Thank You for using Fix YA. Roger

10 MM HEX HEAD SOCKET BIT AND A BREAKER BAR.YOU NEED TO KNOW THE CYLINDER HEAD LOOSE SEQUENCE TO KEEP FROM HAVING CRACKED OR WARP HEAD.YOU NEED HAYNES OR CHILTON MANUAL.BECAUSE SOME EARLY 90S TOYOTA CARS YOU HAVE TO LOOSEN HEAD BOLTS IN SEQUENCE.

Cylinder head bolt removal sequence


Removal sequence: Front 3 7 11 13 10 6 2 1 5 9 14 12 8 4

***CAUTION*** The above sequence must be followed during removal as to avoid warpage of the cylinder head unit

Reverse sequence to install, Step 1: Torque to 10 Ft/Lbs Step 2: Torque to 18 Ft/Lbs Step 3: Torque to 25 Ft/Lbs Step 4: Turn an additional 90 degrees Step 5: Turn an additional 90 degrees Step 6: Torque the 2 recessed 8mm bolts to 13 Ft/Lbs *** CAUTION *** engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper Torque

Don't forget to rate this answer, Good Luck

Fig. : Cylinder head torque sequence, 260, 307, 350 403 Oldsmobile built engines




On the V8, tighten the bolts, in the sequence illustrated, to 100 ft. lbs. When all bolts have been tightened to this figure, begin the tightening sequence again, and torque all bolts to 130 ft. lbs.

On V6's, tighten all head bolts in sequence to the following torques:
* All except bolts 5, 6, 11, 12, 13 and 14 - 100 ft. lbs.(19-135.5 Nm)
* Bolts 5, 6, 11, 12, 13, and 14 - 41 ft. lbs. (19-55.5 Nm)
* All bolts except 5, 6, 11, 12, 13, and 14 - 142 ft. lbs. (19-192.5 Nm)
* Bolts 5, 6, 11, 12, 13, and 14 - 59 ft. lbs. (19-80 Nm)



Hope this help (remember comment and rated this).

Hello vienotkelly: The correct Main bolt torque is 42 foot pounds. The connecting rods torque to 29 foot pounds. The torque sequence for the head bolts and the correct way to tighten the bolts are attached to this reply. Thak You for using FixYa. Roger