Cars & Trucks Logo
Anonymous Posted on Oct 15, 2011

1986 fiero 2.8l vacuum line diagram - 1986 Pontiac Fiero

1 Answer

Rebel A. Faggioli

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Hot-Shot:

An expert who has answered 20 questions.

Corporal:

An expert that hasĀ over 10 points.

  • Contributor 33 Answers
  • Posted on Aug 11, 2014
Rebel A. Faggioli
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Hot-Shot:

An expert who has answered 20 questions.

Corporal:

An expert that hasĀ over 10 points.

Joined: Apr 05, 2013
Answers
33
Questions
0
Helped
31033
Points
36

1986 fiero 2.8l vacuum line diagram - images%5c363.jpg
Hope this helps. A note though, the forward-most valve cover gets fresh, filtered air from the snorkel tube that comes from the air cleaner to the throttle body. A recall changed the source of this fresh air from the pipe along the firewall to the air cleaner, instead sourcing it from the snorkel tube in a futile attempt to prevent engine fires. The rear-most valve cover contains the PCV valve and goes directly to the bottom of the intake plenum.
The "Elek Vac Reg" in the picture is actually called the EGR vacuum control solenoid and it's 'diagnostic' switch. the hose that looks like it goes nowhere should actually be attached to the smaller pipe that runs along the firewall with the 'old, pre-recall' PCV fresh air pipe to the sir cleaner. This hose was left intact after the recall.
If you have cruise control, I believe it just has one line that gets hooked into a Tee that was installed in the canister's constant vacuum supply.



2 Related Answers

Anonymous

  • 3 Answers
  • Posted on Jul 03, 2008

SOURCE: vacuum line diagram

if you get a chilton from any local parts store it should have them in there

Ad
truekleen1

Preacher

  • 46 Answers
  • Posted on May 16, 2009

SOURCE: 1986 Ford Ranger Vacuum lines wrong

Go to auto zone through this link And register for free then click select vehicle, add your vehicle and go to driveability and Emissions controls, than go to vacuum diagrams.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

1986 ferio se 2.8 v6 timming gear replacement

to make the replacement easily you can get help from service and repair manual from the given link this manual comes along with diagram and picture to help you easily and you can fix it own http://toolsnyou.com/
0helpful
2answers

1986 FORD RANGER 2.9L 4WD VACUUM LINE DIAGRAM

I had the same need on an 87 firebird what I did was go to the junk yard find the same truck with same engine and trace the lines make my own diagram, and in my case buy the hard plastic formed vacuum lines that were broken. hope that helps
3helpful
1answer

1987 pontiac fiero won't shift out of first gear automatic transmission. engine was just put back together from pieces. vacuume lines are hanging out don't know where to connect.

heres a vaccum diagram and alao make sure the passing gear cable is connect and adjusted if this car has one which i think it does, also check electrical connections are hooked up,heres two diagrams i labeled them, one is for the 2.5 engine and the other for 2.8 engine connect the vaccum line and retry it, hope this helps.d09847a.gifc3e18c5.gif
0helpful
1answer

Runs rich and miss fires

Make sure the spark plug wires are on right (propper firing order), and check the TPS sensor. Are there any exhaust leaks or vacuum leaks? Did you use the original intake manifolds and Holley throttle body? If not you need to replace the PROM chip with the one from the donor car.
1helpful
1answer

1986 Ford Ranger Vacuum lines wrong

Go to auto zone through this link And register for free then click select vehicle, add your vehicle and go to driveability and Emissions controls, than go to vacuum diagrams.
0helpful
1answer

My 88 Pontiac Fiero transmission (automatic) doesn't shift properly during warm weather. It fails to go into the highest level unless I force to shift by tapping the accelerator.

Hi,

This sounds like you have a dirty transmission filter . I would change the filter and transmission fluid on it . That should fix the problem but if it does not check the vacuum line to make sure it is on and not leaking.
3helpful
2answers

Fuse box

try here http://www.fieronews.net/fusion/downloads.php?cat_id=13 you can download the pdf files

http://www.fieronews.net/fusion/Downloads/Tech%20Downloads/Pontiac_Fiero-86-owners_manual.pdf

contains the fuse box diagram on page 101 of 111 of the pdf reader.
1helpful
2answers

I just bought a 1986 fiero 2.8 v6 when i start the car it run about 5,000 rpms and will not come down to an idle

Check the EGR tube that bolts to the bottom of the upper intake (close to the throttle body) to the EGR Valve for cracks. Also check for Vacuum leaks. Also have the cold start system check for problems. The COLD START INJECTOR SWITCH might be bad.(The cold start injector switch activates the cold start injector on all V-6 Fieros. This switch turns on the cold start injector on initial start up to get the engine to start quicker and run smoother when it is cold.)

0helpful
1answer

Vacuum line diagram

if you get a chilton from any local parts store it should have them in there
Not finding what you are looking for?

3,523 views

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...