Rear brake shoe diagram - 2001 Dodge Dakota

google "diagram 93 suburban rear brake shoe springs" images pop right up. A tip, anytime you need a picture of almost anything just google "image of .....", usually there is a picture of whatever you want.

installing rear brakes with rotors calipers and emergency brake shoes...

I am sorry but we have no diagrams of the brakes of any kind. Please try YouTube, it is a great source of help with these types of jobs.

Rear Brake shoe replacement can be a difficult task at times. Most mechanics replace one sie at a time so that they can look at the other side for reference if needed. You can find step by step brake shoe repalcement here: http://www.freeautomechanic.com/brake-drum-brakes.html

You can also get a diagram in the repair manual link at the bottom of that page.

If the following is not enough then maybe try Alldata.com which generally has more information, but it will cost: REMOVAL & INSTALLATION Chrysler Concorde, New Yorker, LHS Dodge Intrepid Eagle Vision

1. Remove the rear wheels and brake drums.
2. Remove the dust cap from the rear hub and bearing assembly.
3. Remove the cotter pin, nut retainer and wave washer. Discard the old cotter pin.
4. Remove the rear hub and bearing assembly retainer nut and washer. Remove the rear hub and bearing assembly from the spindle.
5. Remove the automatic adjuster spring from the adjuster lever.
6. Rotate the automatic adjuster starwheel enough so both shoes move out far enough to be free of the wheel cylinder boots.
7. Disconnect the parking brake cable from the actuating lever. Disconnect parking brake cable one side at a time.
8. Remove the both lower brake shoe to anchor springs.
9. Remove the 2 brake shoe hold-down springs from the brake shoes.
10. Remove the brake shoes, upper shoe-to-shoe return spring, automatic adjuster and automatic adjuster lever from the backing plate as an assembly.
11. Separate the brake shoes from the automatic adjuster mechanism.
12. Remove the brake shoe automatic adjuster lever from the leading brake shoe. To install:
    
13. Thoroughly clean and dry the backing plate. To prepare the backing plate, lubricate the bosses, anchor pin and parking brake actuating lever pivot surface lightly with lithium based grease.
14. Remove, clean and dry all parts still on the old shoes. Lubricate the starwheel shaft threads with anti-seize lubricant.
15. Assemble both brake shoes, the top shoe to shoe return spring, automatic adjuster and automatic adjuster lever before mounting on vehicle. Make sure the ends of the automatic adjusters are positioned above the extruded pins in the webbing of the brake shoes prior to installation.
16. Install the brake shoe assembly onto the brake support plate and install the hold-down springs.
17. Install the lower anchor springs and reconnect the parking brake cable to the park brake lever of the trailing brake shoe.
18. Rotate the serrated adjuster nut to remove the free-play from the adjuster assembly.
19. Install the automatic adjuster lever spring on the lead brake shoe assembly and the automatic adjuster lever.
20. Install the rear hub and bearing assembly. Install washer and retainer nut and torque to 124 ft. lbs. (168 Nm).
21. Install the wave washer, nut retainer and a new cotter pin onto the spindle. Install dust cap.
22. Adjust brake shoes so not to interfere with brake drum installation. Install the rear brake drum. NOTE: After installing the brake drums, pump the brake pedal several times to partially adjust the brake shoes. To verify proper operation of the self-adjusting parking brake, be sure that both rear brakes are not dragging when the parking brake pedal is released.
    
23. Install the rear wheels and lug nuts. Torque the lug nuts, in a star pattern sequence, to 95 ft. lbs. (129 Nm).
24. Road test the vehicle. The automatic adjusters will continue brake adjustment during the road test of the vehicle.

You can go to autozone.com and register for full free online repair manual that has the diagrams you need and everything else you could want.

Copy and paste this into your search window: 2002 ford ranger rear brake diagram

You should see four pictures pop up, select the brake parts diagram or the brake picture.

help is here:
http://autos.groups.yahoo.com/group/villagerquest/

Drum Removal

1. Remove the rear wheel and the tire assembly. Refer to Section 204-04 .

1. Retract the brake shoes and loosen the brake adjuster screw.

1. Remove the brake drum.

----------------------
May require big hammer to loosen drum from axle flange. Hit between the the lugs, not on them.

------------------------------------------------------------------------------
#10 is access plug to back off adjusting wheel.


Item Part Number Description 1 2261 Rear wheel cylinder 2 — Dust boot (part of 2128) 3 2197 Wheel cylinder piston (part of 2261) 4 — Cup (part of 2128) 5 2204 Wheel cylinder piston cup spring (part of 2128) 6 — Wheel cylinder housing (part of 2261) 7 — Brake shoe hold-down pin 8 — Access hole (part of 2212) 9 — Rear brake bleeder screw (part of 2261) 10 — Access hole plug 11 — Rear wheel cylinder bolt 12 2212 Rear brake backing plate 13 — Rear brake backing plate bolts 14 2N790 Parking brake lever clip 15 — Spring washer 16 — Secondary brake shoe and lining (part of 2200) 17 — Brake shoe hold-down spring (part of 2B514) 18 — Lower retracting spring (part of 2B514) 19 2A637 Parking brake lever 20 — Parking brake lever pin 21 2A177 Brake shoe adjusting lever 22 — Adjuster lever pin (part of 2A177) 23 — Primary brake shoe and lining (part of 2200) 24 — Upper retracting spring (part of 2B514) 25 2041 Brake adjuster screw

--------------
Shoes Removal

Take a picture and remember how each part goes and attaches

1. Remove the brake drum, refer to Drum in this section.

1. Remove the upper retracting spring.

1. Remove the lower retracting spring.

1. Remove the self-adjuster.

1. Remove the hold-down springs.

1. Remove the parking brake lever clip and the parking brake lever.

Drum, Rear Brake System Standard Rear Brake

Item Part Number Description 1 2069 Brake Shoe Hold-Down Spring Pin 2 — Rear Wheel Cylinder Retaining Bolt (2 Req'd) 3 — Washer (2 Req'd) 4 — Anchor Pin (Part of 2211) 5 — Wheel Cylinder 6 2028 Brake Shoe Anchor Pin Guide Plate 7 2A637 Parking Brake Lever 8 2296 Brake Shoe Retracting Spring (Short) 9 2296 Brake Shoe Retracting Spring (Long) 10 2200 Rear Brake Shoe and Lining (Secondary) 11 — Washer 12 2106 Parking Brake Lever Pin Retainer 13 — Brake Shoe Adjusting Lever Cable Guide 14 2A642 Primary Brake Shoe Parking Brake Lever Link 15 2A601 Parking Brake Link Spring 16 2068 Brake Shoe Hold-Down Spring 17 2A176 Brake Shoe Adjusting Lever 18 2048 Brake Shoe Adjusting Screw Socket 19 2047 Brake Shoe Adjusting Screw Nut 20 2041 Brake Adjusting Screw 21 2049 Brake Shoe Adjusting Screw Spring 22 2200 Rear Brake Shoe and Lining (Primary) 23 2A178 Brake Shoe Adjusting Lever Cable 24 2211 Brake Backing Plate
Heavy Duty Rear Brake

Item Part Number Description 1 — Rear Wheel Cylinder Retaining Bolt 2 00538 Lock Nut 3 2212 Rear Brake Backing Plate 4 2262 Rear Wheel Cylinder 5 2A642 Primary Brake Shoe Parking Brake Lever Link 6 2A601 Parking Brake Link Spring 7 2A637 Parking Brake Lever 8 2106 Parking Brake Lever Pin Retainer 9 — Parking Brake Lever Bolt 10 — Secondary Shoe Assembly 11 2A179 Brake Shoe Adjusting Lever Cable Guide 12 2068 Brake Shoe Hold-Down Spring 13 — Adjusting Lever Pin 14 — Adjusting Lever Return Spring 15 2A176 Brake Shoe Adjusting Lever 16 2047 Brake Shoe Adjusting Screw Nut 17 2049 Brake Shoe Adjusting Screw Spring 18 2041 Brake Adjuster Screw 19 — Primary Shoe Assembly 20 2068 Brake Shoe Hold-Down Spring 21 2200 Rear Brake Shoe and Lining 22 2035 Brake Shoe Retracting Spring 23 2A178 Brake Shoe Adjusting Lever Cable 24 2092 Brake Adjusting Hole Cover 25 2069 Brake Shoe Hold-Down Spring Pin
The rear drum brakes:

• Have internal shoes that expand against the brake drum (1126).
• Are a single-anchor type.
• Are actuated by one rear wheel cylinder (2262).
• Have two pistons in the rear wheel cylinder (2261). One exerts force against the upper end of the primary shoe; the other exerts force against the upper end of the secondary shoe.
• Adjust rear brake shoes and linings (2200) automatically.
• Need manual brake adjustment if the adjusters are not operating properly or after the rear brake shoes and linings have been replaced.

When the brake pedal is applied, hydraulic fluid pressure forces the pistons in the rear wheel cylinder outward, moving the rear brake shoes and linings against the brake drum.
The rear drum brake system includes the parking brake mechanism. Refer to Section 206-05 .

If this is for the rear here you go.
http://www.google.com/search?hl=en&client=firefox-a&rls=org.mozilla:en-US:official&hs=2rX&ei=CtiNSdOoLZmktQPLvaWDCQ&sa=X&oi=spell&resnum=0&ct=result&cd=1&q=Ford+Focus+rear+brake+diagram&spell=1