Power locks The door lock on the sliding door does not lock/unlock when I press lock/unlock on the keyfob or the power door switch. All other locks work.

The keyless entry system consists of the following components:

• driver door module (DDM)
• keyless entry transmitter
• keyless entry keypad

The driver door module (DDM) receives inputs from the digital transmission range (TR) sensor, ignition switch, brake switch, window/door lock switches, lighting control module (LCM), keyless entry keypad switch and remote transmitter. The DDM outputs consists of keyless entry keypad switch illumination, power door lock actuators, luggage compartment release solenoid, horn relay, and lighting control module (LCM).

• Battery junction box (BJB) fuses:
  • circuit breaker 7 (20A)
• Central junction box (CJB)
  • 4 (10A)
  • 6 (15A)
  • 8 (25A)
  • 13 (5A)
• Keyless entry keypad switch
• Power door lock actuator
• Luggage compartment release switch
• Luggage compartment release solenoid
• Connectors or connections
• Wiring harness
• If fuse's good have checked for DTC'S - diagnostic trouble codes .
• B1526 Keyless Entry Circuit Short to Ground DDM Go To Pinpoint Test E . B1553 Decklid Release Circuit Short to Battery DDM Go To Pinpoint Test B . B1751 Park/Neutral Switch Circuit Short to Battery DDM Go To Pinpoint Test K . B2425 Remote Keyless Entry Out of Synchronization DDM Go To Pinpoint Test L Need a professional grade scan tool to check fro these codes . Not a code reader for OBD2 codes .

• The doors do not lock/unlock using the remote transmitter

• Remote transmitter not programmed.
• Remote transmitter.
• DDM.

• Go To Pinpoint Test F .

Did you program the new key fob ?

Remote Transmitter Programming NOTE: All remote transmitters are programmable and must be set at the same time.

1. Turn the key from OFF to RUN four times within three seconds, ending in RUN. The locks will then lock and unlock, confirming program mode has been entered.

1. Press any button on each remote transmitter to be programmed. The doors will lock and unlock to confirm that each remote transmitter has been programmed.

1. If additonal remote transmitters are to be programmed, repeat Step 3 within 7.5 seconds or steps 2 and 3 if more than 7.5 seconds have elapsed.

1. To exit program mode, turn the ignition to START or wait 7.5 seconds.

1. NOTE: Failure to wait at least 20 seconds will cause programming failures. Wait at least 20 seconds after turning the key to OFF or after the last remote transmitter has been programmed to activate a remote transmitter for testing or verification

Door Locking / Unlocking Problem - Kia Forum

www.kia-forums.com/kia.../68734-door-locking-unlocking-problem.ht...
May 9, 2011 - 10 posts - ‎4 authors Door Locking / Unlocking Intermittent Problem With Remote Keyfob ... being opendoesn't seem to prevent the car from locking, just the doors ... Power door lock issue
6 posts
May 4, 2015
KIA Sorento 2013 car doors won't unlock while car is ...
6 posts
Jan 20, 2013
Problem with key fob and unlocking the doors
10 posts
Feb 16, 2011
Remote locking fob not working
10 posts
Nov 13, 2010
More results from www.kia-forums.com

It looks like that your 'closed door' sensor is out of order or the door itself doesn't reach it far enough. put something sticky on the tip of sensor and try again.

The alarm is armed if keyfob is used. So you must use the fob to disarm alarm first. So someone can not unlock and open door without keyfob or alarm will be set off.

usaully this is done by the keyfob when u press it to lock the doors,if u take and hold down the keyfob your horn will beep1 time it will lock your doors keep holding it down it should beep again after this unlock your doors this should reset this.

Sounds like the switch is bad. Try passenger side lock button or keyfob lock. If they work and not driver side, then it's the switch in the doorpanel. If none work to lock, but all will unlock, then it's probably the little lock motor inside driver door.

This sounds like a bad power lock actuator,most newer cars the power lock actuator is part of the latch,you can remove the door panel and check for power and ground at the lock actuator and if its getting power on one wire and ground on the other then actuator is bad, power and ground switch bettween wires depending on if your locking or unlocking.

reset the central locking system by locking car with key in drivers door and hold key over for 30 secs.then pressing and holding down unlock button on keypad OR unlock door with key and hold key over 30secs (windows may go down, thats okay,some cars are fitted with auto windows)then press and hold lock button on keypad.making sure that in both cases you know the keyfob battery is in good nick....should reset system

where can i buy a chrysler neon 1998 fobs?

check master door switch/grounds and out put power= if all ok then look at GEM module.