Question about 2005 Dodge Caravan

1 Answer

2005 dodge caravan 2.4 , location of crankshaft position sensor?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    New Friend:

    An expert that has 1 follower.

    Welcome Back:

    Visited the website for 2 consecutive days.

  • Contributor
  • 1 Answer

2005 Dodge Caravan SE 2.4L Engine. Crank Shaft Sensor is located on the front of the engine (side toward the radiator) and right below the starter.
Raise the vehicle on stands or ramps. From under the vechcle, unclip the wire plug. Loosen and remove the 8mm bolt. Pull out old sensor.
This CAN be done WITHOUT removing the starter. Easiest way is to use a deep 8mm x 1/4” drive socket and good lighting. I had to use vise grips to grip and pul out the old sensor. It is okay to twist and pull.
NOTE: I have seen many posts placing this sensor in all kinds of places. For this vehicle, this is where it is located. If you have a different engine or year, it could be located someplace else.

Posted on May 25, 2018

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 44 Answers

SOURCE: location of crankshaft position sensor

it is located on the rear of the engine behind and below the alternator.

Posted on May 21, 2008

Anonymous

  • 30 Answers

SOURCE: 04 Dodge SRT 4 crankshaft sensor

The Crankshaft Position Sensor is located directly next to the starter.

  1. On 2.4L SRT-4 remove the lower inner cooler hose from the metal tube.
  2. Remove the Structural Collar
  3. Unlock and disconnect the electrical connector to the crankshaft position sensor.
  4. Remove the crankshaft position sensor bolt.
  5. Remove the sensor
Reverse Order to install except note that:

Use a twisting motion when installing the sensor.

Install and tighten the crankshaft position sensor bolt and tighten to 9 N·m (80 ±15 in. lbs.).

Posted on Aug 16, 2008

Anonymous

  • 37 Answers

SOURCE: crankshaft position sensor location

Hello. One way to check if it is working is when you try to start the car does the needle move on you tac? If not then your crank sensor is more then likely the problem. It is located on the backside of the engine under the intake manifold. If is in about the center of the block. There will be a 10mm bolt holding the sensor in. If you decide to change it yourself (not to terrible of a job) unplug the sensor, remove the bolt and spin it back and forth slightly while pulling it out. It may be stoburn and you might have to work at it for a little bit (not a done of room) but it will come. When it's out the sensor will be shaped kind of like an L. I have changed a few of these over time and they can be a little stoburn. To install just reverse the process.

Posted on Mar 26, 2009

Bill Hackett

  • 383 Answers

SOURCE: CANNOT FIND THE CRANKSHAFT POSITION SENSOR

cerebral_eni: The crank position sensor is located at the back of the engine block just below the cylinder head. It actually projects into the bell housing and reads the teeth on the flywheel where it references TDC for #1 cyl and RPM's of the crank. It's a "Hall effects generator". Unless you are into electronics and have a lab scope to look for a square wave pattern, I will continue with my other input.
Nissan has a recall campaign on the crank angle sensors.
The campaign # is 07V527000:ECM update for stalling;
NHTSA07V527000 NOV 07,
The symptom was brief malfunction of sensor causing the engine to quit running which could potentially put the vehicle at risk for a collision. The sensors would ultimately fail. There was also a voluntary recall on the reprogramming of the ECM's due to stalling problems. TSB# NTB07-081, Campaign ID#R0712
I hope this information is of some assistance to you. You may be able you get your car repaired under warranty! Good Luck!

Posted on Apr 08, 2009

rvrfsh

Chris

  • 3 Answers

SOURCE: location of crankshaft position sensor

I have a 2005 neon and i found mu crank sensor on the radiator side of the block driver side of center directly below the starter. I hope this helps..

Posted on Apr 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is located the crankshaft position sensor for 2005 dodge sprinter 2500


Is this a deisel motor? If so, it will not have a crankshaft sensor

Jul 19, 2015 | Dodge Cars & Trucks

1 Answer

Location of Crankshaft sensor on 2005 Dodge Caravan SE: 2.4 Liter. Is crankshaft sensor location the same as 3.3 Liter?


The crankshaft position sensor mounts to the engine block behind the alternator near the oil filter.

Jul 12, 2014 | 2005 Dodge Grand Caravan

1 Answer

2005 Dodge Neon SXT 2.0L crankshaft position sensor location to replace


P0315 - Crankshaft Position System Variation Not Learned
P0335 - Magnetic Crankshaft Position Sensor Electrical Error China OBD2 car diagnostic tools wholesale on CareUCar

Mar 20, 2014 | 2005 Dodge Neon SXT

1 Answer

Crankshaft position sensor


1996 Dodge Truck Caravan 2WD 3.0L MFI 6cyl

The Crankshaft Position Sensor is located:Under hood, driver side, rear engine area, mounted top rear of engine .click here and enlarge picture,it's number 9,send picture to your library and you can enlarge even more.Here's the part.Here's how to remove.

Feb 03, 2013 | 1996 Dodge Caravan

2 Answers

Replace crankshaft position sensor in 2003 dodge caravan 3.3 V6


According to Haynes, the V6 engine has the sensor mounted in the bellhousing on the back of the engine.

Aug 20, 2012 | Dodge Cars & Trucks

1 Answer

Where is the crankshaft position sensor on a 2003 dodge caravan 33L V6 engine


Hi there:
The 3.3/3.8L crankshaft sensor is located on the rear of the transmission housing, above the differential housing (The bottom of the sensor is positioned next to the drive plate...




8_21_2012_9_41_28_pm.gif

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Aug 20, 2012 | Dodge Caravan Cars & Trucks

2 Answers

Want to locate where is the crankshaft sensor on 2005 dodge grand carvan 3.3 eng


Hello brscwb,

Below is an image depicting the location of the crank sensor.

I hope this helps.

netvan_130.png

Regards,

natven

Aug 02, 2011 | Dodge Caravan Cars & Trucks

2 Answers

Where is crank sensor located on a 1991 dodge caravan 3.3 engine


For 1991 Dodge Truck Caravan 4WD 3.3L MFI 6cyl the Crankshaft Position Sensor is located: Under hood, center, rear engine area, where transaxle bellhousing meets engine, mounted in engine block.

Hope this Helps (remember to rate and comment this).

Oct 02, 2010 | 1991 Dodge Caravan

1 Answer

I pulled codes from a dodge grand carvan the code is p0016 crankshaft sensor b1 sa1 replaced and replaced camshalf sensor also still did not fix the problem what other part should i look at


Hello! The DTC P0016 inidicates a cranskshaft and camshaft misalignment. If you only replaced the camshaft position sensor - you may need to replace the crankshaft position sensor - which is located at the top where the engine and transmission connect.


Hope this helps and good luck! Thanks for using FixYa!

Oct 16, 2009 | 2005 Dodge Grand Caravan

Not finding what you are looking for?
2005 Dodge Caravan Logo

Related Topics:

1,726 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...