2001 sebring failed nj inspection - obd code p0601 - how to fix?

Hi Charity,here's a link on your P0601 code. http://www.obd-codes.com/p0601

Hi Again,here's another link,to your P0601 code. P0601 OBD II Trouble Code

po601= internal controller failure, internal control module fault condition ( check sum ) detected .

internal controller failure =po601

P0601-INTERNAL MEMORY CHECKSUM INVALID
Need a new PCM. Make sure it is new and correctly programmed for your mileage.

http://www.obd-codes.com/p0601

P0601 - Internal Control Module Memory Check Sum Error

Basically that means that there is an interal fault in the Powertrain Control Module (PCM). There have been many reported PCM failures on Chrysler/Dodge products although it is possible for this to happen on any vehicle. In Dodge/Chrysler products, a P0601 trouble code means that a serial communication failed inside the computer at least 6 times.

Symptoms: Likely, no symptoms will be discernible to the driver, other than the illuminated Check Engine Light. Typically the engine runs fine, gauges work, etc.

Causes: A code P0601 in most cases means the PCM has gone bad. This is possibly due to a short-circuit inside the PCM. Or, if you disconnect the wires/connector from the PCM while the battery is still connected, that may also cause this code.

Possible Solutions: With a P0601 OBD-II trouble code, the most common fix is to replace and reprogram the PCM. In a few cases the dealer may be able to reflash the PCM and get it working. But more than likely the PCM will need to be replaced and reprogrammed (we recommend you take it to a dealership for this). The good news is it *may* be covered under your emmissions warranty. So even if you're out of bumper-to-bumper warranty or powertrain warranty, check your warranty guide or dealer to see if this is covered.

Other people have reported that they cleared the code only for it to return again and again. Keep in mind that most shops can replace the PCM but not all can program it.

Other PCM / ECM Codes: P0602, P0603, P0604, P0605, P0606, P0607, P0608, P0609, P0610.

Hope this help to solve it (remember rated this).

P0700 - Transaxle Control System Fault Conditions
The P0700 code is for information only and the next step is to check for transaxle codes in the Transaxle Control Module (TCM). So you'll have to have the dealer or another qualified shop/technician pull the transaxle codes from the TCM and go from there.

P0740 - Torque Converter Clutch Circuit Malfunction

P0601 - Internal Control Module Memory Check Sum Error
What does that mean?
Basically that means that there is an interal fault in the Powertrain Control Module (PCM). There have been many reported PCM failures on Chrysler/Dodge products although it is possible for this to happen on any vehicle. In Dodge/Chrysler products, a P0601 trouble code means that a serial communication failed inside the computer at least 6 times.

Symptoms
Likely, no symptoms will be discernible to the driver, other than the illuminated Check Engine Light. Typically the engine runs fine, gauges work, etc.

Causes
A code P0601 in most cases means the PCM has gone bad. This is possibly due to a short-circuit inside the PCM. Or, if you disconnect the wires/connector from the PCM while the battery is still connected, that may also cause this code.

Possible Solutions
With a P0601 OBD-II trouble code, the most common fix is to replace and reprogram the PCM. In a few cases the dealer may be able to reflash the PCM and get it working. But more than likely the PCM will need to be replaced and reprogrammed (we recommend you take it to a dealership for this). The good news is it *may* be covered under your emmissions warranty. So even if you're out of bumper-to-bumper warranty or powertrain warranty, check your warranty guide or dealer to see if this is covered.

Other people have reported that they cleared the code only for it to return again and again. Keep in mind that most shops can replace the PCM but not all can program it.


Good luck!

P0125 OBD-II Trouble Code
Technical Description

Insufficient Coolant Temperature For Closed Loop Fuel Control
What does that mean?

This means that the engine coolant temperature (ECT) sensor indicates that the engine has not reached the required temperature level to enter closed-loop operation within a specified amount of time after starting the engine.
http://www.obd-codes.com/p0125

P0601 OBD-II Trouble Code
Technical Description

Internal Control Module Memory Check Sum Error
What does that mean?

Basically that means that there is an interal fault in the Powertrain Control Module (PCM). There have been many reported PCM failures on Chrysler/Dodge products although it is possible for this to happen on any vehicle. In Dodge/Chrysler products, a P0601 trouble code means that a serial communication failed inside the computer at least 6 times.
http://www.obd-codes.com/p0601

SYMPTOM
P0601-PCM INTERNAL CONTROLLER FAILURE

TEST NOTE
This symptom is diagnosed using the test P0600-PCM FAILURE SPI COMMUNICATIONS.

WHEN MONITORED
Ignition key ON.

SET CONDITION
Internal checksum for software failed, does not match calculated value.

POSSIBLE CAUSES

• PCM internal or SPI