Lowbeam headlight not working

low beam won't light Richard, faulty bulb socket module or wires, check and repair.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

How to Fix Low Beam Headlight

Low beam headlights out High beam working

High beams ok but not low beam one side only TDIClub Forums

make sure the connections are clean and no wires are broken.

When either the high or low beam light is out in either side, DRL (daytime running lights) indicator will come on. When one bulb goes out, that's a clue the opposite bulb will burn out soon, so its best to replace both bulbs. If it was a fuse issue, both left and right side would be out. If driver side is OK but passenger side is not, then its a bulb issue. A 2006 Honda civic takes 9006 (HB4) low beam bulbs and 9005 (HB3) high beam bulbs. Cheapest is online from Walmart site-2-store. After procuring, wear latex, vinyl, or ANY gloves to keep your (corrosive) oil skin from coming in contact with headlight glass bulbs. Your skin oil will chemically react and cause shorter life span on glass bulbs. Instruction don't tell you this, so you handle with your hands, then need to replace bulbs 3 years later instead of 5 years (or more) in the future. With gloves on, pop the hood and look behind each headlight. Turn counter clockwise to unlock headlight bulb holders. Its a quarter to half turn to unlock bulb holder lock. Replace one bulb at a time so you don't confuse high beam from low beam. The wire has a tab you need to lift to pull out & disconnect wire connector. You might need a slim narrow-**** (NOT phillips) screwdriver to lift the tab; or use your house key. Snap the wire connector to the new bulb, then twist into headlight housing to secure bulb holders, then move on to the next bulb to repeat the procedure. Pict below, 9005 high beam is on the left, 9006 low beam is on the right. Handle by grasping the plastic base, not the glass bulbs. The raised potrusion on the bottom center is where the tab locks onto wire connector. Replace all 4 bulbs now, but in the future, its likely the low beam will wear out before the high beam. In the future, replace only the pair, not all 4. The factory installs inferior bulbs that go out sooner, hoping you'll take to dealership and they ******** you with higher parts-n-labor fees. As opposed to Walmart online site-2-store, it would cost you AT LEAST triple in parts & labor from dealership to replace all 4 headlight bulbs :-(

This is usually caused by a failed front control module as this unit controls the lighting on the vehicle!
--------
airbag reset tool

check the fuses as it has a fuse for each headlight if iam not mistaken

The dimmer switch on the stalk usually operates a relay in the fuse box.
It could be the dimmer switch, relay, lowbeam fuse, or odd coincidence both lowbeam filaments went out.
Use a test light and work backwards.

Check the fuse. There are seperate fuses for right and left. You dont mention if the high beam works for that side? If it does, the fuse is good. The GREEN wire at the bulb is the ground for the low beam. If that wire has power, then the ground is bad. If the high beam works, the hi'lo beam switch is good, and there is a problem between that headlight and the Engine Compartment Junction Block

Hi,
It has been because the lamp bulb or halogen lamp module has reached the end of its serviceable life, not because of any wiring problems. Low beam burns out first because it is on the most. If low beam is lost simultaneously in both headlights, I would check fuse first, then the headlight switch. If low beam is lost on one side only, it is almost always going to be due to the bulb or lamp module needing to be replaced. In that case, replace them in both headlights because the other one will be going kaput in short order, as well.
Most like the low beam filiment is bad but the high beam filiment is still good, try replacing bulb. If replacing bulb does not fix problem then you probably have voltage problems and should check the voltage reading and the plug.
OR
isolate the wire that comes from the headlight switch to the headlamp bulbs for low beam and check to see if there is a short in the wire. You can find this wire by using a test light turn on the key and get a good ground with the test light poke the wire and see if the test light illunimates with the headlight switch on.
check the wires, and check the fuse for your lowbeams. could of blown a fuse on your lows, but your highs will still work.

The fuse box is located in the engine compartment,on the driver's side. Has thumb-screw retained cover.
Thanks for contacting fixya.com

check the wire connection for your lowbeams

you need to check for power at the low beam wire on the connector on the headlight...need to see if it is getting power...if it is...bad connectore or socket for the buld...if not ...need to chase wiring problems