Torque specs of head bolts for 1994 mighty max pick up

Mitsubishi Mighty Max crankshaft bolt Questions & Answers ...

www.fixya.com > ... > crankshaft bolt > Cars & Trucks > Mitsubishi

Mitsubishi Mighty Max cars & trucks crankshaft bolt questions and answers. ...Torque specs for mighty max The head torque specs for 1991 mitsubishi mighty max 2.4 I ... 1989 mitsubishi 2.0 motor crankshaft was turned while timeing belt was off. ...how to install a clutch kit on my 1994 mitsubishi mighty max Disconnect the .

Torque new cylinder head bolts in sequence to 44 ft lb. Loosen bolts approximately two turns, then torque bolts in sequence to 44 ft lb. Turn bolts an additional 90 degrees in sequence, then an additional 90 degrees

Torque sequence
9 3 1 5 7
8 6 2 4 10

Assuming 3.0 V6, per my manual:

All in FT pounds torque,unless noted:

Main bearings: 60
Connecting rod bearing cap nuts: 34
Rocker arm shaft bolts 180 INCH POUNDS
Intake manifold: 168 INCH POUNDS
Exhaust manifold nuts: 18
Crankshaft vibration dampner bolt: 112
Cam shaft sprocket bolts: 70
Head bolts: 76 - 83
If you need others please let me know, when working with Aluminum parts go easy as they can strip easy.
Please let me know if this helped,
Tom

I really really really hope you turned the bolts an additional 90 degrees after torquing to 22 Ft-lbs. Otherwise, you may be taking that head off again.

Best of luck,

David

Per my Chilton's manual tehe bolts should be (cold engine) 65 to 72 FT. Pnds., the cam shaft bearing bolts should be 8x25 = 15 - 19 Ft pnds and the 8x65 should be 14 - 15 Ft Pnds.

The sequence is as follows for the (10 ) head bolts:

7 - 5 - 2 - 4 - 10

9 - 3 - 1 - 6 - 8

I hope this may help,
Tom

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below

85 foot lbs start in center work your way out start at 45 ft lbs then 65 then 85

Intake bolt torque is 11-14 foot pounds. Note:
to torque bolts & nuts, start in center using
crisscross pattern working outward. And as Far as the sealant goes, you shouldn't need any additional sealant since the new gasket has sealant.(just make sure both surfaces are clean an free of oil.) sometimes if the head or the block show signs of pitting on the matteing surfaces then you could use a litttle of that cooper spray gasket to coat the new gasket.

Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): Foot pounds (Final torque) Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. Foot pounds (Final torque) Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

if its a four cylinder(lets hope)the specs are 80-90ft.lbs torque.if its a six cylinder it is 14ft.lbs torqueat 90 degree intervals then repeat until correct torque has been reached.bad news is you can not use the same bolts on the six cylinder engine.have to be new to keep from breaking them