I have a 2001 nissan altima and sometimes my car wont go over 60mph would that b gas filter issue or mass air flow sensor

I would suggest a plugged fuel filter or bad fuel pump. Maybe bad or stuck Mass Air Flow Sensor.

Hi Chris.

p0304 = Number 4 Cylinder Misfire Detected

Faulty spark plug 4
Clogged or faulty fuel injector 4
Faulty ignition coil 4
Fuel injector 4 harness is open or shorted
Fuel injector 4 circuit poor electrical connection
Ignition coil 4 harness is open or shorted
Ignition coil 4 circuit poor electrical connection
Insufficient cylinder 4 compression
Incorrect fuel pressure
Intake air leak

The P0304 code means that the cylinder 4 is misfiring or is randomly misfiring. Start by checking for intake leaks an if no leaks are found the next step is to replace the spark plugs on cylinder 4.


p0102 = Mass or Volume Air Flow Circuit Low Input

Faulty mass air flow sensor
Intake air leaks
Dirty mass air flow sensor
Dirty mass air filter
Mass air flow sensor harness is open or shorted
Mass air flow sensor circuit poor electrical connection

Before replacing the mass air flow sensor, try replacing the air filter and cleaning the air flow sensor with low compress air or mass air flow sensor cleaner.
Reset code and drive vehicle.
If the code comes back, it may be necessary to replaced the mass air flow sensor.


p0154 = O2 Sensor Circuit No Activity Detected Sensor 1 Bank 2

Faulty Front Heated Oxygen Sensor Bank 2
Front Heated Oxygen Sensor Bank 2 harness is open or shorted
Front Heated Oxygen Sensor Bank 2 circuit poor electrical connection
Inappropriate fuel pressure
Faulty fuel injectors
Intake air leaks may be faulty
Exhaust gas leaks

Replacing the Front Heated Oxygen Sensor Bank 2 usually takes care of the problem.


p0113 = Intake Air Temperature Sensor Circuit High

Faulty Intake Air Temperature (IAT) sensor
Dirty air filter
Intake Air Temperature (IAT) sensor harness is open or shorted
Intake Air Temperature (IAT) sensor circuit poor electrical connection

The Intake Air Temperature (IAT) sensor is built into mass air flow sensor or in some vehicles mounted to the air filter duct housing. The sensor detects intake air temperature and transmits a signal to the Engine Control Module (ECM).The temperature sensing unit uses a thermistor which is sensitive to the change in temperature. Electrical resistance of the thermistor decreases in response to the temperature rise. The Intake Air Temperature signal is used as an input for various systems in the vehicle.



Hope this helps
FYT

http://www.autocodes.com/make/nissan

Have to look up the specs

In general you need about 16 oz (Volume) in 15 to 20 seconds

ok lets start with the codes they say your getting. P??? which 1's and how many. there are few o2 sensors, are they next to the Exhaust next to the converter? MASS AIR FLOW -MAF use this, for now i am guessing, until i see the correct codes your are getting. this could be the 1 you may have below, please read it........

• P0103
  Mass Air Flow Sensor Circuit High Input
• Possible causes
• Faulty mass air flow sensor
  - Intake air leaks
  - Dirty mass air flow sensor
  - Dirty mass air filter
  - Mass air flow sensor harness is open or shorted
  - Mass air flow sensor circuit poor electrical connection
• Before replacing the mass air flow sensor, try replacing the air filter and cleaning the air flow sensor with low compress air or mass air flow sensor cleaner. Reset code and drive vehicle. If the code comes back, it may be necessary to replaced the mass air flow sensor.
• possible symptoms Engine Light ON (or Service Engine Soon Warning Light)
  - Engine stall
  - Engine running rough
  - Excessive fuel consumption
  - Excessive smoke
• the code is generated when An excessively high voltage from the sensor is sent to Engine Control Module (ECM).

2003 NISSAN Altima Sedan OBDII Codes List

Mass air flow not MAP ?
Nissan Infiniti Mass Air Flow Sensor Testing Replacement P0100

P0100 NISSAN - Mass Air Flow Sensor Circuit Range/Performance Error

Possible causes- Dirty mass air flow sensor
- Dirty mass air filter
- Mass air flow sensor harness is open or shorted
- Mass air flow sensor electrical circuit poor connection
- Intake air leaks
- Faulty mass air flow sensor
Tech notes Before replacing the mass air flow sensor, try replacing the air filter and cleaning the air flow sensor with low compress air or mass air flow sensor cleaner. Reset code and drive vehicle. If the code comes back, it may be necessary to replaced the mass air flow sensor.

It sounds like you have an issue with your PCM-powerterain control module.

P0300: Random / multiple cylinders misfire.

P0111: Intake Air Temperature Sensor. But sometimes this code comes up if you got a dirty air filter/Defective Mass air flow too.

But first you have to do is check the misfiring first and see if you need new spark plug or plug wires. Good luck bro

Removal and Installation To Remove:

1. Remove or disconnect the following:
   • Mass air flow sensor electrical connector
   • Tube clamp at the electronic throttle control actuator
   • Air cleaner to electronic throttle control actuator tube, upper air cleaner case
   • Mass air flow sensor from the cleaner case.

To Install:

1. Install or connect the following:
   • Mass air flow sensor to the cleaner case
   • Air cleaner to electronic throttle control actuator tube
   • Tube clamp at the electronic throttle control actuator
   • Mass air flow sensor electrical connector

Clean the MAF (mass air flow sensor.)Follow the hose from the air filter to the air flow sensor.Use a proper cleaner rated safe for this purpose.