What is the torque setting for the front hub nut on a peugeot expert 2.0l 2001

The torque setting for the nuts on a 1996 Peugeot 306 hatchback will depend on the size of the nuts and the type of bolts they are used with. Here are the recommended torque settings for some of the more common fasteners on the Peugeot 306:

• Wheel nuts: 80-90 Nm
• Engine oil drain plug: 25-30 Nm
• Engine oil filter housing: 25-30 Nm
• Engine oil cooler hose banjo bolts: 25-30 Nm
• Engine oil pump mounting bolts: 25-30 Nm

These torque values are for general reference only and may vary depending on the specific model of the Peugeot 306 and the condition of the fasteners. It is always best to refer to the manufacturer's recommendations for the correct torque settings.

The one that fits!

That's not the way it works. you buy a socket set. It has one set of AF Sockets and one set of Metric sockets. The one you use is the one that fits.

Hub and Wheel Bearing Torque Specifications - DRiV

drivcat.com > HubWheelTorqueTableWindow

2009 Ford Fusion ... Front Proc 1 Note ... Front Proc 2 Note ... Do not attempt to tighten the nut with the vehicle on the ground or the wheel bearing will be ...

Front Axle Nut Torque Spec - Lounge - Fusion Energi - Ford ...

www.fordfusionenergiforum.com > topic > 6160-front-...

Dec. 2, 2019 - Im replacing the front wheel bearing assemble this weekend and cant find the torque spec for the ale nut. The older model Fusion (up to 2012) ...

BHA54317 Axle / Spindle Nut Torque Specification - 1A Auto

docs.1aauto.com > BHA54317 Torque Spec

PDF Vehicle Notes. Lb. ft NM. Ford. Fusion. 2006-12 (Excluding All Wheel Drive Models). Rear. Lincoln. MKZ. 2007-12 (Excluding All Wheel Drive Models). Rear.

SKF-Front-Rear-Axle-Nut-Hub-Mount-Lug-Nut-Torque-Spec

dannysengineportal.com > wp-content > uploads > S...
PDF
Front & rear axle nut, hub mount and lug nut torque specifications for FWD ... 3 Series AWD E92, E93 ....2012-2013 . ... FORD / MERCURY TRUCKS - cont.


..

325 nm.

The torque for the hub bolts is 120 ft. lbs
The torque for the axle nut is 185 ft. lbs.

On an LDV pickup convoy 05 plate how tight do you make the front wheel bearing nuts

Did you torque the axle nut to the correct torque setting?

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

36mm

The torque for the front drive shaft and hub retaining nut is 155ft.lbs. But if you are on the metric system,
it's 210N.m . These specs are for both 1999 and 2001
Hope this helps. Good luck.

Tightening torque for the hub nut is 200Nm and the road wheels are 85Nm

NOTE: The rear wheel bearings are remowned on these cars for sticking to the stub axle quite badly, and often have to be forced off using a slide hammer on the drum, it is quite common to end up damaging the wheel bearing, so be prepared to replace this as well in this event

THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS