Tip & How-To about Jaguar XJ8

Simple steps to replace the Valve Cover Gaskets on a Jaguar XJ8?

Replace the valve cover gasket if the valve cover gaskets are leaking or if they're worn. The procedure is as follows:--
1)First carefully remove the nuts holding the valve cover to the engine head.2
2)Then pull the valve cover off from the engine head .
3)You can use flat-tip screwdriver to remove the valve cover.
4)It will be very dirty inside so you will have to clean the mating surfaces on both the engine head and the valve cover.
5)Take your time and clean it completely.

6)You can use a bead of RTV sealant on both mating surfaces.

7)Then carefully seat the gasket to top of the engine head.
8)The gasket can only be fitted in one way. So fit it properely.
9)Then tightly Press the valve cover to the gasket
10)And tighten the valve cover nuts secure.

This will help.Good Luck.

Related Questions:

0helpful

1answer

valve cover won't come off

Follow the detailed procedure mentioned in the link below to remove replace VALVE cover:----
Click the link below:---
VALVE COVER GASKET REMOVAL GUIDE http://technoanswers.blogspot.in/2012/06/valve-cover-gasket-removal-guide.html

-----------
For more help on these issues,check the link below:---
Car oil leaks from valve cover gasket? http://schematicsdiagram.blogspot.com/2011/12/car-oil-leaks-from-valve-cover-gasket.html

--------
Lexus RX: Tapping noise under Valve Cover At Low RPM? http://technoanswers.blogspot.in/2012/04/lexus-rx-tapping-noise-under-valve.html
---------- How to replace Timing Belt,Water pump And Valve Guides on Mitsubishi Montero http://repairhelpcenter.blogspot.com/2012/10/how-to-replace-timing-beltwater-pump.html

----------
2000 Toyota Solara: Valve Cover Gasket Replacing? http://technoanswers.blogspot.in/2012/04/2000-toyota-solara-valve-cover-gasket.html

----------
Valve Cover Keeps Cracking? http://schematicsdiagram.blogspot.in/2012/04/valve-cover-keeps-cracking.html

----------
These details will help.
Thanks.

Read full answer

Nov 23, 2012 • 2006 Subaru Forester

0helpful

1answer

How to remove/replace the Valve Cover Gaskets on a New Beetle car?

Read full answer

Mar 09, 2010 • Volkswagen Beetle Cars & Trucks

0helpful

2answers

How to replace valve cover gasket

Remove the valve cover, which is a simple bolt on component. Remove the old gasket and install the new one.

Read full answer

May 13, 2011 • 2004 Suzuki Forenza

0helpful

1answer

how to replace valve cover gasket 1998 chevy malibu

The first step is to remove all the parts that are in the way of you being able to remove the valve covers. (Ex.: air intake, loose wires etc.) Then you will need to remove your valve covers (using basic tools) and be very careful to not let anything get on your lifters, which your valve covers protect. Once you have the valve covers off compare the new gaskets to make sure they are the right size. Then remove the old gasket and replace with the new one using a high temp gasket sealant (available at any auto parts store) to attach the gasket to the valve covers. Then tighten down snug and check for leaks after replaced.

Read full answer

May 05, 2009 • Chevrolet Malibu Cars & Trucks

0helpful

1answer

Leaks oil looks like from valve cover

You have to remove the spark plugs cables and remove the four nuts that you see when the cables are removed.

When the four nuts are removed, simply raise the valuve cover. When replacing the gasket, make sure you get the gromets as well. Those sometimes get worn or crack since they are more exposed than the value cover gasket. Make sure that you clean the cover from oil and replace the gasket with no use of silicon.

Good Luck.

Read full answer

Jul 20, 2008 • 1999 Toyota Camry

Not finding what you are looking for?

2,403 views

Ask a Question

Usually answered in minutes!

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Simple steps to replace the Valve Cover Gaskets on a Jaguar XJ8?

Related Topics: