20 Most Recent 2003 Chevrolet Chevrolet Malibu LS Questions & Answers

Hi Stephanie: Water coming out the exhaust can be normal, BUT, if there is white vapour and the fluid level in the radiator is going down, that is a key indicator of a bad head gasket. You could TRY a TEMPORARY fix with a radiator sealant, but replacing the head gasket can get expensive. A compression test will tell you if there is a bad head gasket. Also, check the dipstick to see if there is any indication of oil in the crank case. Hope this helps.

Replacing spark plugs and ignition wires on 2001 Chevy Malibu 3 1 6

It is going to be a seal that needs to be replaced. It will cost you a whole lot less if you get it fixed now.

ther is a wiper delay unit under the day follow the buzzing I’m happy to assist further over the phone at https://www.6ya.com/expert/james_1cb31da1bc8c6102

Some potential solutions: EGR (Exhaust Gas Recirculation): You mentioned that you cleaned the EGR, but it's still showing as a fault. The EGR system recirculates exhaust gases back into the intake manifold to reduce emissions. If the EGR valve is malfunctioning or clogged, it can affect engine performance. Here are some steps to consider: Check for Vacuum Leaks: Inspect the vacuum lines connected to the EGR valve for leaks or cracks. A vacuum leak can disrupt EGR operation. Test the EGR Valve: Use a vacuum pump to check if the EGR valve opens and closes properly. If it doesn't, consider replacing it. Clean the Intake Manifold: Sometimes carbon buildup in the intake manifold can affect EGR flow. Clean the intake manifold thoroughly. Thermostat: You've already replaced the thermostat, which is good. A faulty thermostat can cause overheating or poor engine performance. Make sure the new thermostat is functioning correctly. System Voltage Low: This could be related to the charging system (alternator, battery, or wiring). Here are some steps to troubleshoot: Check Battery Voltage: Measure the battery voltage when the engine is off and when it's running. It should be around 12.6V when off and around 13.8-14.4V when running. Inspect Alternator: Ensure the alternator is charging properly. If it's not, consider replacing it. Check Grounds and Wiring: Loose or corroded connections can cause voltage issues. Inspect battery terminals, ground connections, and wiring. Idle Issues: If the engine won't idle properly, consider the following: Idle Air Control Valve (IACV): The IACV controls idle speed. Clean or replace it if necessary. Throttle Body Cleaning: A dirty throttle body can affect idle quality. Clean it using throttle body cleaner. Vacuum Leaks: Check for vacuum leaks around the intake manifold, hoses, and gaskets. Timing Chain: The B12D1 engine uses a timing chain. However, if it's stretched or worn, it can cause issues like poor performance or stalling. Consider having the timing chain inspected and replaced if needed. Remember that diagnosing engine issues can be complex, and it's often best to consult a professional mechanic or use diagnostic tools.

Tensioner pulleys are designed to be 'Self Adjusting'. These pulleys are on spring loaded arms so they automatically push against the belt keeping it tight. You use a socket or a spanner to swing the pulley arm back against this spring. *Note* This is a powerful spring so BE CAREFUL when your working on it! A lot of these tensioners have two small holes to help with installing a belt. When you swing the tensioner arm back these two holes line up with each other. You can then slide a hex key, or something similar, through both holes and it holds the arm back giving you space to get the belt on. *Caution* When your ready to release the tensioner DO NOT just pull the hex key out!! With the socket or spanner you used to swing the tensioner arm back push the arm against the spring again, carefully pull the allen key out then Carefully release the pressure on the spring so the pulley sits correctly and tensions the belt.

Help in the link. It may be a faulty switch, but you can test it. https://www.google.com/search?q=2012+Chevrolet+Orlando+open+jammed+hatch ..

check the abs system for relay and electrical problems the clicking can be from a cycling relay and the head lights flickering from the power draw for the abs away from the head lights.

You either replace the whole board as a module, or a company like RS Components, or even Amazon can sell you just the solder-on USB socket. https://www.google.com/search?q=usb+port+replacement ..

The oil cooler runs through the radiator and when damaged can exchange fluids.

google 1994 Chevrolet C1500 5.7 l ransmission control module select images and you will see module.

Unfortunately this question is part English and part Spanish aclienders? auto magic transformation? ..

The reverse wire on the car audio harness for a 2006 Chevrolet Silverado is yellow. If you're connecting an aftermarket stereo, this wire is used to trigger the reverse camera display when you shift into reverse. Make sure to connect it appropriately for your specific installation needs.

I would go to an AutoZone, or similar parts store, that does free code scans, they can explain what's going on.

https://www.mahle-aftermarket.com/media/local-media-north-america/pdfs-&-thumbnails/torque3.pdf Check this manual

Question edited to better English. https://www.google.com/search?q=1995+GMC+Pickup+8+cylinders+automatic+wiring+diagram ..

I'm guessing you mean knock sensor wire. If you need just the end of the wire you should be able to order a pigtail from any parts store and just but connect it on