2008 Toyota Camry - Answered Questions & Fixed issues
How do you remove the backseat of a 2008 Toyota Camry
Step 1 Slide the two front seats forward. This may not be necessary, but it will give you more room to work.Step 2 Pull the seatbelts out of the slits at the back of the cushion. You are not removing the seat belts, just moving them out of the way.Step 3 Remove the mounting bolt from the rear seat cushion with a socket wrench. You will have to lift up the front edge of the cushion to get at this bolt. Then, pull the cushion up and out of the Camry.Step 4 Locate the seat back locks and undo them by pulling them up.Step 5 Move the seat backs down and remove the mounting bolts with a socket wrench. These bolts will be located at the center hinges. Pull the seat back up and out of the Camry.
3/20/2022 7:57:46 PM •
2008 Toyota...
•
Answered
on Mar 20, 2022
•
165 views
Speedometer
you need to locate the speedo wire, it can go like this. read wheel to the abs. to the sunroof motor to the auto box then ecu, and anything else before it gets to the speedo in the dash any one of these were is not connecting properly can give this code. also check the cog on the read wheel make sure its not mucked up. also if the abs is not lite up to say there is a fault its not that part that is the problem.
2/19/2018 5:46:04 AM •
2008 Toyota...
•
Answered
on Feb 19, 2018
•
229 views
Charging system light on
The charging system in your vehicle is computer controlled ,checking for DTC'S - diagnostic trouble code's should alway's be the first step in the diagnostic process ,testing for B+ voltage at the wiring connections at the alternator would be the next step if no DTC'S are stored . The single heavy gage wire on the back should have Battery voltage , the wire's at the connector ,three out of the four should have B+ voltage an the # 3 wire is the control circuit from the ECM - engine control module . Four fuse's supply B+ voltage to these connections . 10 amp gauge #1 , 7.5 amp gauge #2 , 7.5 amp ALT-S an 120 amp ALT fuse. If any one of these is blown the alternator won't charge . If you know nothing of automotive electrical system testing ,your best bet would be to take your vehicle to a qualified repair shop.
11/10/2017 2:16:12 PM •
2008 Toyota...
•
Answered
on Nov 10, 2017
•
110 views
Engine Drone at 2500 RPM
I would loosen every engine and trans mount and slide a piece of rubber between the mount and the body and retighten,this may change the vibration to level you can live with.
8/28/2017 12:49:42 AM •
2008 Toyota...
•
Answered
on Aug 28, 2017
•
680 views
Manual key won't unlock doors or trunk
If not the wrong key, maybe the locks are seized from not being used. Over time with humidity, and lubricants drying up inside of the mechanics of the locks they could seize. When inserting the key the pins are not properly moving in to place to allow the tumbler assembly to turn.
Try using some silicon lubrication. Spray in to the lock. Work the key in and out of the lock a few dozen times before attempting to turn. Then spray in some graphite lock lubricant. Insert the key in and out a number of times. Then tap on the key end with something hard like a pliers or something not to heavy or forceful. Then try turning the key. Jiggle it a bit and moving it in and out. Eventually the pins should normally release and position themselves.
If all of the above does not work, then you will need to get a lock smith to assist. Most likely he will be able to get in to the vehicle so he can remove the locks to service them.
4/2/2017 6:36:40 PM •
2008 Toyota...
•
Answered
on Apr 02, 2017
•
3,351 views
Where is the fuel pump on 2008 camry
It's inside your fuel tank. Most have a access plate that you can get at the fuel pump without having to drop the tank and you have to look and see where your tank is that it is right up above if it's around where the back seats and that's probably where it's at
8/26/2016 9:15:31 PM •
2008 Toyota...
•
Answered
on Aug 26, 2016
•
156 views
Not finding what you are looking for?