20 Most Recent 2006 Toyota Sequoia - Page 7 Questions & Answers

The computer turns your traction control off when it sets the check engine light. Thats why VSC lights come on at the same time. Have the local parts store see what code you are getting to find the problem.

You need to remove the coil packs that are located above the valve cover. It is important to get the correct spark plugs from toyota. Aftermarket plugs are not recommended.

Check the throttle body and see if it has build up around the butterfly. If so, clean the butterfly with throttle body cleaner. This may be it. There are other possibilities but this is a simple inspection.

Hello!

If you are referring to the ( ! ) symbol, it indicates that you have an issue with your tires, one of more being low on air.

It is the tire pressure warning light.

Hello.I will be glad to help you out.

Choose which of the 3 buttons you wish to use, on the car.

Take the remote transmitter, depress the actuator button, and continue to hold it until advised to release.

Depress the button, on the car, of your choice, and hold it down until advised to release.

Hold the garage door actuator (while holding the actuator button down) above the car's 3 buttons.

Rotate the door transmitter until the red light above the 3 buttons starts to flash slowly.

Stop moving the remote around when the light flashes slow.

Within several seconds, the same light n the car will now flash rapidly.

Release the car's button, release the transmitter button.

Verify that the door now operates..

by what your saying the key that you are using has a chip in side of it some times if the key goes near a magnet it will kill the program in the key. if you have a spare key try that key. if you don't what you might have to do is bring your car and key to the dealer to have them programed. but that red key on the dash board is telling you that sercurity has been turned on so that no one can steal it with out that key that you have. try that good luck

you may need to replace the airbag if the clockspring has already been replaced

My 2001 Toyota Sequoia just lost all dash lights last night too. I've tried checking the fuses in the cabin, and none of them look blown. Did you ever get an answer to this problem?

There is most likely a problem with the disk that you are trying to play. Either the disk is not in a format that the player understands or it is scratched, or the data is corrupted. Try a different disk.

If several disks are doing the same thing, then your DVD may need cleaning. There are Cleaning disks available at your local electronics outlets that you can pop into your DVD player and it will clean the lenses on the optics inside the player.

Hold the button on your Homelink unit for 20 seconds. The light will begin to blink fast.

Place the remote door opener within one inch of the homelink console and press and hold the button on the remote until the light on the homelink unit begins flashing slower, long blinks.

The code is programmed.

If the programming fails, try restarting the process, but pushing the remote button and holding, then repushing and holding, as some remotes do not transmit long enough to program.

Here is the factory directions for reference, it is a very large picture so I linked it:
http://img190.imageshack.us/img190/6337/2006toyotatrucksequoiap.jpg

try http://www.etrailer.com/faq-wiring.aspx. This should help. Mike

Yoy need to replaced the rear door handle and poss latch.
You can get the door open by removing the door panel and manually pulling on the latch cable

no.. common concern.. back handle breakes becausr of bad latch.. remove back panel from inside.. gain acess. will be able to open from there.. replace handle latch or both

check the fuse

this beep came on when any of wheels is sliping at moment, its not problem

yes it needs to be taken apart and the regulator needs to be set at zero and the window all the way to the top, you can loosen the bolts to pry the gear away from the track and force it all the way to the top then bolt it back together. it was not puttogether in the frist place and if a mechanic did it take it back and get it done for free, there should be a warrenty on it.

If your vehicle has similar controls like my 2006 Sequia. put the ignition in the ON position... then press the Tire Pressure Monitor Reset button (it is located on the dashboard button right beneath the streering wheel column).. press it for 4 to 5 seconds till you see the pressure monitor light come on and then go off. That should reset the system.

It sounds like the handle has become disconnected from the mechanism. You will have to remove the inner door panel and reattch. It is not a complicated or difficult job but if you get a professional it could cost upwards of $100.

its normal for every toyota to do this. its not hard on you engine it helps remove carbon build up

If you raise a air ride suspension any **** should know to disconnect the compressor before jacking up the vehicle as it will blow the bags.....