20 Most Recent 2006 Toyota Sequoia - Page 5 Questions & Answers

The brake pads may be new, but the rotors sound like they may be bad. If they are they will ruin your new pads. This might also be your ABS kicking in, Feels different because of the new brakes. Either way I would have a qualified shop inspect your brakes, this is cheaper than rear-ending someone.

Call your local Auto Zone or Advance Auto Parts, they may be able to reset the light for you. I know they can run diagnostics and can reset a Check Engine light, they may be able to do more.

back door hardware is connected throug a control box wire attahced to the door; so if problem with remote it is a different problem.... if the back window try this home made solutiojn:
remove the back door cover, let an assistant hold down either the remote button or the panel switch down, and hit the window motor gentle-wise!!! it should work
good luck

yes i does !

Upply the handbreak "sidebreak" and you will have a picture. This is a safety feature by the dvd/navigation manufacturer.
Hope this helps.

Usually sound is heard through car speakers not by screen... so there might be power problem with screen. If not, you just need to check video cable connected vetween player and screen.

propably, cabling issue: there should be connectors for: every side speakers, another for video and it could be either not inserted all the way or shortened some where.... check it

use the extension rod with jack set (as if will use the jack)... open the rear door, insert it all the way in the hole near by door lock (exactly infront of you facing the back opened!), then keep turning it anti clock wise.... good luck

as it broke, you need to replace the handle only! then use Anti rust spray to the lock from time to time... it'll be ok! the lock is exposed to accumalation of dust, dirt and lubricants as it is in the bottom of the door, so you need to take more care about it. handle will cost you $60 to $72
if you have some skills you can do it your self, or take it to a technician

Bentley publishes the best, most comprehensive manuals available. other than the factory manuals from toyota, they are best. good luck!

with the key off press and hold the trip reset button in the instrument cluster while you turn the key to the run position. The display will turn to dashes and then they will start to disappear. The all zeros will appear and then the odometer will again be shown. Release the button and the maintenance light will be reset.

Sometimes the odometer needs to be on trip A before turning the key off and pressing the button. I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

6.5 Qts. Use 5w/30 motor oil

Here's how you get reset the MAINT REQD light:

1) put the key to the ON position
2) press the mileage reset button on your cluster so it shows total mileage (not trip)
3) put the key to the OFF position
4) press and hold down the mileage reset button, leave it pressed
5) put the key to the ON position
6) wait until the mileage shows 000000 and you can stop pressing the ODO button

If that doesn't work, consult this

http://www.tundrasolutions.com/forums/tundra/115807-reset-maint-reqd-light/

this is your low tire pressure indicator light , it means one of you tires air pressure is lower than it should be , check you tire pressure on all tires and inflate as needed once they are correct than the light will go out , keep an eye on the tire that was low , you may have a slow leak

i believe there are 2 total but 1 fuse box is in the engine compartment driver's side and another is a fuse box in the passenger compartment lower trim panel fuse box. Now to figure out what is which, If you flip the cover of the fuse box over, when you take it off and expose the fuses. You will see the diagram of where each fuse for each function is. Good Luck.
if you require further assistance please let me know and i will be glad to assist you furthere- Thanks, Midwest-tek

i beleive VSC is for veh. speed cotrol (cruise cotrol)

sounds like the linkage is hookup wrong and may be backwards, the release and lock/unlock linkage are in the wrong holes reverse the two and try it, this sounds like the problem.