1994 Toyota Previa - Page 8 - Answered Questions & Fixed issues


fsm quote
The fuel filter is located under the vehicle on the drivers side near the charcoal canister. Access is much easier from under the vehicle.

and some have a protective shield
in all cases, following the fuel line from tank youd have seen the filter.
for sure.
1995

Toyota Previa... | Answered on Feb 01, 2014 | 168 views


You can download very easy the service manual for toyota previa. Recommend this website, is 100% safe.

Toyota Previa... | Answered on Jan 06, 2014 | 312 views


A/T car, auto or stick>
if A/T check the levels,,,, of fluid. ATF.
my guess. is the engine races real fast and car dont move,
right, this is called transmission slip or FLARE.
there are 2 issues, here, no engine power, RPM very low.all time.
or trans slip.
its one or the other.

Toyota Previa... | Answered on Jan 02, 2014 | 98 views


FSM
buy one, at,, drum rollllllllll, toyota.

Toyota Previa... | Answered on Dec 22, 2013 | 38 views


The first thing to check is the clutch release mechanism for faults. If a cable check that the clutch operates fully from dis-engaged to engaged as if the pressure plate is held 1/2 off then the clutch will slip. If hydraulic the same fault will be from a master cylinder that has a blockage in the compensating port. It is cheaper to fix the operating bits before pulling out the gear box because normally if a clutch is worn out or the pressure plate is broken you will go nowhere regardless.

Toyota Previa... | Answered on Dec 11, 2013 | 219 views


tail is park, so turn off the parking lights ,.there are 20+ lamps
inside and out for park/tail/dim dash lamps.
do you mean stop lights stuck on, id bet so. (parks out)
so replace or adjust the brake lamp switch.
see alldata.com for full facts on topic.

Toyota Previa... | Answered on Dec 07, 2013 | 225 views


Adjust the brake pedal switch located on the upper side of the brake pedal under the dash. To adjust the stop light switch, disconnect the two wires attached to the rear of the switch, move the switch by loosening the lock nut towards the brake pedal. As soon as the center pin of the switch begins to touch the brake pedal notch, rotate the switch half turn more and lock it by tightening the lock nut. Connect the wires back and ask your companion to see the tail lamps while you depress and release the brake pedal. Or you can see the tail lamp behavior by parking the car on reverse at a distance of one foot from any wall.

Toyota Previa... | Answered on Dec 06, 2013 | 155 views


Change fuel filter first. Could be a number of things but you aren't giving enough information.

Toyota Previa... | Answered on Nov 03, 2013 | 39 views


Check antifreeze,coolant,thermostat could be seized controls when engine is hot for heat

Toyota Previa... | Answered on Nov 02, 2013 | 129 views


Cut the old terminal plug and tap it to aftermarket blower motor so that you can use the same plug without any hazzle. But please make sure you tap it to the right polarity, the positive and negative.

Toyota Previa... | Answered on Oct 18, 2013 | 34 views


Did you get the timing marks in the right place? All wires plugged in?

Toyota Previa... | Answered on Oct 16, 2013 | 50 views


Normally, this is caused due to Sand or not enough lubrication. If you do not have some technical knowledge on it , it will be wise to take it to a repairman

Toyota Previa... | Answered on Oct 15, 2013 | 143 views


That could be very dangerous. It could be bad wheel beaings or a broken suspension part. Could also be something wrong with the power steering but be safe and get this checked out by a shop asap.

Toyota Previa... | Answered on Oct 11, 2013 | 40 views


It could be:
-Poor fuel. (Not enough pressure)
-Bad injector. (Not open and let fuel in when NEED)
-Burn or broken spark plug wire (So it spark to metal instead at the tip of the spark plug)

Mai

Toyota Previa... | Answered on Oct 10, 2013 | 24 views


please RUN the scanner and computer for diagnostic. can be a sensors faulty. and make the TUNE UP. some cable, spark plug, or EMP defective, or coil.
God bless you

Toyota Previa... | Answered on Oct 02, 2013 | 278 views


check for worn or broken motor or trans mounts

Toyota Previa... | Answered on Sep 03, 2013 | 146 views


remote for my Ford Taraus will work inside car, but not on the outside.

Toyota Previa... | Answered on Aug 04, 2013 | 18 views


Can you remove plug.

Toyota Previa... | Answered on Jun 10, 2013 | 60 views


Do a compression test to check for bent valves Check cam shaft position sensor. Check crank shaft position sensor Have the fault codes read for info as to what may be wrong.

Toyota Previa... | Answered on Apr 27, 2013 | 224 views


One is on the slave and one is on the clutch master cylinder.
Do the master first-at the bleeder or at the line 3 times.
Then go to the slave cylinder.
Do not pump the pedal-just old it down to bleed.
the slave may not have a bleeder screw- just crack the feed line to bleed it.

Toyota Previa... | Answered on Mar 03, 2013 | 149 views

Not finding what you are looking for?
1994 Toyota Previa Logo

219 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

1992 Toyota Previa
1992 Toyota Previa

231 Questions

1993 Toyota Previa
1993 Toyota Previa

-106 Questions

1991 Toyota Previa
1991 Toyota Previa

210 Questions

1995 Toyota Previa
1995 Toyota Previa

191 Questions

1997 Toyota Previa
1997 Toyota Previa

-55 Questions

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...