20 Most Recent 2004 Toyota Camry Solara - Page 2 Questions & Answers

looked in my alldata book (europeon version) and this vehcle can only be done by the dealer ,their is something about a previa and pushing button A which is behind a grommet on the dash but its obvious you do not have this so as in common with a lot of dealers they will not reset the light unless they service the vehicle ?? Hence a service light you cannot put out

that is the message center button

It dependes your best bet is to look at the belt for cracking on the under side or other signs of ware like a glaze on it The tenisioner also plays a big roll in this system and is the leading cause of belt failure if its not holding the belt tot that will cause ware I can't see it so you need to look at it and if its never been changed its probably time to do bolth of them but if the belt looks ok then maybe you can get away with just the tenisiner witch is the likely cause of the problem good luck

If it looks like a horsehoe, its a view of the tire. so you need to have your tire pressures checked. Use the pressure on the drivers door jamb, plus 3 psi if tires are warm

The odo-button dance procedure to reset the light is listed in Page 122-123 of the US 2004 Toyota Prius Owner's Manual (Section 2-5 "Operation of Instruments and Controls: Gauges, Meters and Service Reminder Indicators", item (j) in the "Service reminder indicators and warning buzzers" section). It should be listed in a similar section in your Toyota Camry Solara's Owner's Manual.

i would replace the belt. if the belt breaks you could bend the valves. i had mine break at about 102,000. bent 4 valves. I’m happy to help further over the phone at https://www.6ya.com/expert/kenneth_3efc1f8510674f04

Yep! You should replace the TiMiNG BELT and TENSiONER bearing!

Error code reader is only way to clear error codes and reset light.

You need to reset the maintenance reminder manually after you change the oil. You can do this by holding in the trip reset button and turning the key to the run position. keep holding the button down. the odometer should switch to all dashes and then the dashes will start to disapear. once there all gone it has been reset. Sometimes the trip odometer needs to be on a sometimes it needs to be on b. Your owners manual will have further instructions if you need then. I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Check if the front panel is loose any ops, and the audio would pop). The poping variation of up and down volume is caused by a DC voltage somehow getting onto the speaker outputs.
Initially Simply remove and resolder the audio PA and the main connector it should solve the problem ,Otherwise electronic volume control IC is going bad.Will have to replace the IC
Thanks. keep updated for any more query.you can rate this solution and show your appreciation.

When the cable comes off, it usually is a sign that one of the plastic gears has broke. They don't get fixed, they get replaced, a fairly easy job, get the new operator in hand, and take out the old operator, remove all the bolts, glass, support the glass with a wedge, remove the motor, remove the operator through the biggest hole in the door you can find, it might take some straining but it will go. Replace the same way. The shop wants $250 for t his job, The part is about $50. I did all mine myself. No problem. Hope this helps.

check back of radio make sure your speakers attached or plugged in

The laser is out of alignment.
It will require professional servicing to re-align and clean.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Look I had the same trouble. What i did was take out the seats, Remove the carpet. dry out all the water with a few old towels. After you dry it out. Put a fan on it. use a hose or go out in the rain and look for leaks. its a door seal or a window seal. fix the leak and test one more time. clean the rust off and paint with rust killing paint. Clean the carpet while its out with a house shampoo machine.
hope i was helpfull

Maintenance light is turned on when your vehicle is due for service. It is set to turn on at a certain mileage. At minimum, you need an oil change service and what ever is required at your mileage interval. Resetting the light is as simple as, Ignition Key in the off position, press and hold the odometer button, Turn the ignition key on and continue to hold the odometer button for at least ten seconds. If properly done, you will see dashes across your odometer as you hold the button, until the odometer reading reappears. Hope this helps. Please leave feedback.

Try this: Remove the negative battery terminal for 5 minutes. Reconnect the battery termional and see if the CD player "resets" itself. This sometimes works for me.

I think the best bet for you is to go to Alldata.com on line. You can purchase for a reasonable fee the instructions on you vehicle on all kinds of repairs.
This is the same data base proffessionals use.

Good luck

On the lower left hand side of the dash, near the Traction control button, is a small push button. Just press and hold until the Tire Pressure light goes out. Of course, make sure you're pressure is ok, otherwise, it will just come back on in a couple minutes.