20 Most Recent 2002 Hyundai Santa Fe - Page 9 Questions & Answers

Explain the bolts head type & location & what your problems are Going to need the correct drivers for the bolts or fastners

with out further info I would guess sending unit on fuel gauge is bad,that would be located in fuel tank

This job requires special tools and training. There is serious personal injury exposure!!!,
The oiling of the system needs to be addressed, the receiver/dryer needs to be replaced, the system needs to be evacuated....etc, etc.
Have a qualified shop do this for you.

I'm not sure what you mean by "under load", maybe with a/c on, etc. Also is it really an engine misfire or a rough idle. If it really is a misfire, a scantool at your local parts store should be able to read a code for that. Sometimes a rough idle could be due to just a cracked or disconnected vacuum hose or dirty throttle body. You didn't say whether it runs ok at highway speeds. Sometimes a rough idle can be cleared up a lot with throttle body service or injector flush. Sorry, this is the best I can do with information provided.

Most likely a Oxygen sensor.

front or rear?

Rear wheel sensor issue most likly the issue metal flakes on the sensor causeing the computer to think car is in a lost traction condition there fore retarding motor speed to slow car down to a safer speed to regain traction without applying brakes usuall need to remove sensor an clean with a soft bristle tooth brush to remove metal glakes on the speed sensor. Usually there are two on rear axle an two abs sensors in front both have to match rotation speeds if one sensor is off by a fraction it senses the car is hoing into a wheel spin condition or low inflation in one tire in the rear if pass sidebtire is low on air pressure it will throw of the amount of revolutions per min ratio left at 65 miles an hour 6300 rpm right side at recc air pressre 6500 rpm per min 200 rpm difference tricks computer your in a wheel spin have sensors checked for metal debri or dirty sensor may have a broken wire or dirty If you need further help, I’m available over the phone at https://www.6ya.com/expert/robert_c7b5aba9012a13b2

Most likely isse is a blown fuse or burnt relay turn on a/c to verify if other fan comes on if not 60 amp fuse is burnt or relay If you need further help, I’m available over the phone at https://www.6ya.com/expert/robert_c7b5aba9012a13b2

Speed sensor is usually found under the brake booster has a clamp down retainer and pulls up an out need to disconnect battery when installing item to reset computer after replacement some year models require recalibration has to be done by dealer with proper eqipment If you need further help, I’m available over the phone at https://www.6ya.com/expert/robert_c7b5aba9012a13b2

the reason Hyundai suggest a belt change at 60k is that when it does snap, your looking a $3 to $4000 for a engine rebuild,and in England we have an unlimited mileage warranty for 5 years and the belt/engine is covered, if its changed at the proper time(60k).i think its called insurance,you have to have it,but you hope it never happens...ask someone who has had a belt snap.....any make...
some makers are going back to chains.....

Yes both relay and switch are possible.Needs to be inspected.Blower motor replacing for all vehicles? http://repairhelpcenter.blogspot.in/2012/02/blower-motor-replacing-for-all-vehicles.htmlBlower motor Resistor shorting problem?

http://schematicsdiagram.blogspot.com/2011/12/blower-motor-resistor-shorting-problem.html

How to remove Blower control switch? http://howtobyme.blogspot.in/2012/02/how-to-remove-blower-control-switch-on.html

---------

Where is blower motor relay located ? http://technoanswers.blogspot.in/2012/02/where-is-blower-motor-relay-located-on.html

--------

This will help.Thanks.

the sensor has a bolt fixing so an appropriate sized spanner is all thats required tool wise Labelled no 6 by the thermostat housing

Replace the ignition cylinder assembly

Fuel filter is inside fuel tank. It is an integral part of the fuel pump. It can be replaced but ONLY by very qualified mechanics. Fire explosion risk is too high.

Let me know if this helps...

the ignition coil pack assembly on the 2.7 liter Hyundai is known for going bad. it cost about $150 what is a shame is that i have a good one in my garage lol

gratis. good luck there. huh. most cars, have 20 to 50 pages on that. so you think someone is going to scan that and post that? we uses alldata.com but that costs only $15, about 1/7 of and hour shop labor my guess you cant afford shops, sure who can. but not the $15 ????? really??? the cost of floor mats at walfart? here is the discounted link http://www.scantool.net/software/alldata-diy-1-month-subscription.html if savvy , (ask) you can down load the thing. ask. and next time, now you have it. on a memory stick no more guessing. all there. or buy the FSM.