20 Most Recent
Hyundai Motor 1998 Accent - Page 6 Questions & Answers
High beam wont work
Is quite common with a worn headlamp switch. In fact, I have replaced 2 for myself in the past 5 years (different vehicles). Pickup a new switch at your local auto parts supply. If your uncertain about installation you can look up the replacement procedure in a Mitchell, Motor's or Chilton's manual at your local library.
<<If this solution helps to resolve your problem then please take a moment to rate this post.>>
Where do the wires go when wiring a starter motor
the neg wire goes on the bolt that holds the starter, there should be a positive cable wire that goes to the big bolt on the back of starter seleniod and then a small wire that goes to the small connection on the seleniod,then then neg goes to the block or one of the bolts that holds the starter in,
The RPM meter always read over 1500 rpm .. and the
The check engine light comes only when the computer control unit (called the PCM) senses a fault in the electronic controls of the engine and/or the emission system, there are about 200 possible faults that turn the light on, to know what has developed a problem you must have the system tested, this is called an OBD2 fault code test, Kragen and Autozone parts stores do this testing for free.
Whining noise at low speed
If the noise happens when car is in park and you rev it to about 1500rpm's then its thebearing in the oil pump of the torque converter.It should make noise all the time even in park ideling. You may need a rebuild transmission. Have the vehicle checked out at a transmission repair shop
Car not starting - Intermittent
intermitten problems are the worse, when it wont start check fuel pressure with a gauge, and then check for spark, i have spent days on problems such as this, what you have to find is what is missing, fuel ,spark, is maybe coolant leaking into one or more cyls, i have seen air in the fuel system that only cause problems when under hood temp is high, open the hood and it cools enough to to start, hope this helps
The door mechanism has rusted and broken in the
You will need to oder a new latch asembly with linkage if its separte,most times its complete, also take a look at the handles to make sure they are not also rusted. as far as where to get the parts,you can order on line at any dealership and have them sent to you, as far as auckland, new zealand has a dealership.hyundai motors new zeland ltd, phone # 09 836 1270. located @ 1/97 central park drive , henderson auckland. hope this helps.
There is no spark in one spark plug of 4 cylinder
bad spark plug, bad or corroded connection in the spark plug boot, bad spark plug wire, loose or corroded connection on coil post, or bad coil. but if possible... take a plug wire off a known good one ( if length will allow) and swap positions around, if it has spark, then you know your coil and spark plug are good and its time to get a new plug wire;( you should replace all of them though), Now if it doesn't, then the coil is probably bad. can i get a very helpful..thanks!
Airbag lamp accent-98
Hello. The sensor for one of your airbags has most likely gone bad. The only safe fix is to replace it. Joe
How to remove
take the steering column plastic cover off now you should be able to put your key in and turn it to the one possition. with the key in the on possition there should be a hole in the top or bottom of the column rite under where the lock cylinder goes in, use a small screwdriver to push in the hole and just pull the ingnition lock cylinder out. if you dont have a key a lock smith is your best bet
Why does my auto gearbox not go into 4th when the
Sounds to me like u have a faulty ( pulse generator sensor) u can find it at a dealership for less than 80 dlls. it can be easly replace by anyone its : a 1 plug conector wire that divides into 2 sensors like a ( Y ) ull find it under the air filter right on top of the transmission just follow the wire and ull find the second sensor under the transmision, once replaced, i let the key to on position for 15 min to reset the
computer ,and ur good to go..car runs like new again..hope this helps ... Marcos
We need to know where the cam timing marks go on a
Hi
The cam dowel should be at 12:00. the hole in the cam sprocket should be line up with the cam dowel, with cam sprocket assembled to cam, you will see looking through the cam sprocket a red marking on the head, which lines up with the dowel. Down at the crank, make sure the cut out mark on the crank spocket is lined up with the notch on the oil pump cover.
Thanks for using FixYa - Steve
Not finding what you are looking for?