1997 Hyundai Elantra - Page 9 - Answered Questions & Fixed issues


hi this sounds like the elec operated coolant control valve has failed? common fault on ford models however to confirm this? if you warm engine to normal then turn temp setting to full hot do not put fan on yet! locate the heater hoses from engine to point they go into bulkhead of engine bay? feel each hose for heat ? if one is warm/hot and other much cooler/cold ? then cooler valve is not opening so coolant can flow thro heater matrix inside car understand?? unfortunate;y this valve is not servicable but is easy to change and not too expensive ? its location is normally at point prior to entering car interior and you will find it if you follow heater hoses? it may well be in bay below the grill below w/screen is normally plastic renewal will be apparent when you see it ? hope this helps ? just one point all above is on assumption you have checked radiator coolant level is topped up ?? if not this will also give no heat thro heater ? if very low

1997 Hyundai... | Answered on Oct 28, 2008 | 619 views


gently tap with rubber hammer while pulling

1997 Hyundai... | Answered on Jul 26, 2008 | 65 views


1. Drain the coolant and disconnect the coolant outlet pipe connection hose from the coolant pump. 2. Remove the drive belt and engine coolant pump pulley. 3. Remove the timing belt covers and the timing belt idler. 4. Remove the coolant pump mounting bolts, then remove the generator brace. 5. Remove the coolant pump assembly from the cylinder block. See an exploded view:
d0ab616.gif

1997 Hyundai... | Answered on Jun 27, 2008 | 1,181 views


http://www.2carpros.com/how_to/transmission_service_4.htm
Popular Problems Checks
1. Car will not go into gear:
  • Gear selector cable has failed
  • Brake lock solenoid has failed not allowing the gear selector to move out of "Park"
  • Excessively low transmission fluid (note: if car is operated for an extended amount of time with low fluid level the transmission will fail prematurely)
  • Shorted electrical component not allowing the PCM to control the transmission. Example: shorted fuse
  • Flex plate (flywheel) is broken completely not transferring engine power to the transmission.
2. Car goes into gear but then fades out of gear or is slipping while driving:
  • Transmission fluid is low
  • Transmission clutch discs or bands are worn out or burned
  • Faulty transmission shift solenoid.
3. Car goes into gear but does not shift out of first:
  • Blown fuse to the PCM controller
  • Faulty vehicle speed sensor (VSS)
  • Shorted second gear control solenoid
  • Faulty transmission controller (PCM)
Tips About Common Problems and Fixes

1997 Hyundai... | Answered on Mar 12, 2010 | 897 views


I think idle speed control actuator must also be checked.
If you are not familiar with such repairs better take it to an authorized service shop.

284d390.gif


1.
fuel pump revoval Remove the rear seat cushion. 2. To reduce the internal pressure of the fuel lines and hoses, first start the engine and then disconnect the electrical fuel pump connector. Be sure to reduce the fuel pressure before disconnecting the fuel main pipe and hose otherwise fuel will spill out. 3. Disconnect the battery cable from the negative terminal of the battery. 4. Remove the high pressure hose and fuel return hose. 5. Remove the fuel pump assembly. cb98972.gif

1997 Hyundai... | Answered on Jun 09, 2008 | 893 views


I just got the same message today...and rarely use the cd player. Was wroking, went to change cd's, then it would not load and gave error 43...anyone?????

Hyundai Elantra... | Answered on Sep 26, 2019 | 1,152 views


Im not sure if your fuse box looks like the screenshot however if it does I would at your own risk turn this switch off and back on as suggested in the other photo.
Again I am not a mechanic, I do however try to give the best advice I can.
Hope this helps.
9_12_2019_3_41_38_am.png9_12_2019_3_41_40_am.png

Hyundai Elantra... | Answered on Sep 12, 2019 | 118 views


Check the fuse and relay related to the AC. Your fan should come on when the AC is turned on. Right now the fan is working only off the engine temp., not the AC.

Hyundai Elantra... | Answered on Jun 12, 2019 | 57 views


Hose is held to suspension strut with c-clip, loosen and retighten union joint while still in clip for ease of undoing. then remove clip holding hose with pliers
Top up reservoir and to avoid fluid loss, Clamp existing rubber hose off above Wheel cylinders callipers. Spread brake pads slightly to clear disc rotor edge then undo callipers from hub - suspend from strut with cord or wire and unscrew old pipe. Immediately replace existing with new hose to callipers. With master cylinder reservoir sealed airtight undo union nut at top of existing rubber hose where clipped to strut. Replace existing lower hose fitting with new hose.Tighten union. replace c clip and bleed brakes at nipple on callipers until all air out of lines.
Job done road test for hard pedal repeat bleeding as necessary.

Hyundai Elantra... | Answered on Jun 03, 2019 | 31 views


you need a good scanner to program it to the car

Hyundai Elantra... | Answered on May 31, 2019 | 36 views


Use a good scan tool which should identify the failing sensor/circuit when the vehicle stalls,so you can do the correct repair.

Hyundai Elantra... | Answered on May 19, 2019 | 100 views


By pass clutch signal by appling +12vdc to A/C clutch directly - check for proper suction side pressure with A/C gauge connected to suction side of compressor - if pressure is low clutch will not be energized do to low pressure cutout switch. Add freon or 134A to bring up suction side pressure. https://www.6ya.com/callphilipforhelp

Hyundai Elantra... | Answered on May 19, 2019 | 31 views


Sounds like the beginning of a bad 02 sensor. If your engine light is on that’s the issue. I could almost guarantee it. Any auto part store will read the ecu codes for free.

Hyundai Elantra... | Answered on May 15, 2019 | 26 views


You would have to ask a dealership. If Google doesn't know, then no one does and this code doesn't exist.

https://www.google.com/search?client=firefox-b-d&q=hyundai+elantra+with+a+drain+reset+code+9.76A

Hyundai Elantra... | Answered on Feb 24, 2019 | 31 views


Possible issue with the clutch pedal lock out switch. This switch will not let the engine start unless the clutch is full depressed.

Hyundai Elantra... | Answered on Feb 14, 2019 | 31 views


See if ur ableto shift it at the trany with ur hand into gear go to underhood or under car to the transmission disconnect the leankage should popoff with screw driver maybe hard but it just pops up have someone start car hold foot on brake with ebrake on and shift it one click should be reverse take ebrake off and see if it goes in reverse if it does its ur shift solinoid right there werelinkage clips on if dont its inside ur transmissoin

Hyundai Elantra... | Answered on Jan 02, 2019 | 23 views

Not finding what you are looking for?
1997 Hyundai Elantra Logo

289 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...