20 Most Recent 1995 Hyundai Scoupe - Page 7 Questions & Answers


Their is a rod that runs from inside handle to a lever that pulls up on the latch mechanism. The outside handle has a rod that runs to the same place, what I have seen is the rod running from lever to mechanism come loose at the mechanism and neither handle will work.

Hyundai Cars &... | Answered Yesterday


Hi buddy
Was just browsing through so I read your query. I suggest u try reliable-store.comfor such problems. It's got these manuals that are amazingly helpful in all auto problems and errors, troubleshooting, breakdowns, wirings etc everything.

Hyundai Cars &... | Answered 2 days ago


During acceleration or deceleration the engine moves on rubber mountings and a defect in the exhaust or intake pipework could open so either exhaust or intake roar would become louder - of course it might be something else...

Hyundai Cars &... | Answered 3 days ago


Early airbag (or SRS) systems used only one sensor but later vehicles used several sensors possibly daisy-chained together, at least one of which would be fixed to the front bulkhead behind the dashboard...

Hyundai Cars &... | Answered on Nov 10, 2019


All the knowledge you need is in service and repair manual with diagram and you will get the manual from the given link https://toolsnyou.com/

Hyundai Cars &... | Answered on Nov 10, 2019


Does the effect both the Front and Rear or just one? Does it work when you use the Emergency Flasher? If so, then we know that the fuse and bulb are good. If it worked with the Emergency Flasher then problem would reside in the Turn Signal Stalk or the wiring leading to it. I generally look for loose connectors or plugs. If it did not work replace the bulb. If that does not resolve the issue I would follow the ground wire from the bulb to make sure that there is a good ground. Without the ground you do not have a complete circuit.

Hyundai Cars &... | Answered on Nov 10, 2019


The service and repair manual with diagram will provide you step by step help to locate and fix the problem easily and you will get the manual from the given link https://toolsnyou.com/

Hyundai Cars &... | Answered on Nov 07, 2019


Fob didn't work so the alarm immobiliser was armed and active when the locksmith opened the car - with predictable results.

Fob still not working - broken or needs new battery. Have you fitted a new battery into the fob?

The alarm immobiliser will probably remain armed until the doors have been locked and then unlocked with the fob.

There is a small chance the system can be fooled into thinking it has been disarmed by disconnecting the battery (overnight if poss) and then with the door open and the ignition key in and turned on, when the battery is reconnected it might be possible to start the engine...

Hyundai Cars &... | Answered on Nov 06, 2019


if this is a manual transaxle the reverse lamp switch is just behind the battery box beside the slave cylinder mount. if this is an automatic transaxle it is built into the trans range switch that shift cable moves on top of transmission.

Hyundai Cars &... | Answered on Nov 03, 2019


this has two fuses for clock in under dash fuse box fuse 11 10amp and fuse 3 15 amp

Hyundai Cars &... | Answered on Nov 03, 2019


Hyundai has a tsb on this code it is 16-at-005 basically it breaks down to this: remove air cleaner find extension motor wire disconnect and measure resistance on pins 2 and 7 which if looking at male pins top row from left over 2 and bottom from left over 2 is pin 7 resistance is 112-142 kila ohms now disconnect trans temp sensor connector measure the resistance on pin 4 top row from left and pin 8 bottom row from left should be same 112-142 kila ohms at outside temp 68 . if reading are not the same resistance replace transaxle,if they both are same resistance replace HPCU (hybrid power control unit ) next step if resistance is different by 1 ohm harness is good,if resistance on both readings are different by more than 1 ohm replace extension wire . may need to send this car to dealership if this testing is more than you can provide yourself,sorry hope it helps

Hyundai Cars &... | Answered on Nov 03, 2019


That is the hydraulic tappets waiting for oil pressure. Change the oil and filter. Use only the recommended grade of oil. See your owners handbook.

Hyundai Cars &... | Answered on Nov 02, 2019


what year Hyundai? which bolts are you looking for torque settings for exactly?

Hyundai Cars &... | Answered on Oct 26, 2019

Not finding what you are looking for?
1995 Hyundai Scoupe Logo

59 questions posted

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Motor S Hyundai

  • Motor S Hyundai

Most Popular Question

2004 hyundai coupe 2 0se

  • Cars & Trucks
Loading...