20 Most Recent Hyundai Motor 2003 Elantra - Page 9 Questions & Answers

There is a fuse box to the left of the steering wheel. The little compartment that opens up there can be totally removed to reveal the fuses. There is a fuse diagram on the back of the compartment. There should be a spare fuse for each amp level used and a plastic tool to remove or replace fuses with. There is another fuse box under the hood on the same side as the battery and driver side headlight.

i would check with some carexperts

pump could be bad. have it checked.

Looks like a clutch master cylinder or slave cylinder malfunction.

most of the time a engine light will set with an Evap leak code if the gass cap is not tight or left off. tighten cap, or replace cap if gasket is cracked or worn.

For Doors not getting open with remote or key problem,or door parts removal ,there are help links provided below. Click the link below to go through its procedure and troubleshoot the problem: ---- Drivers side front door will not open from inside or outside?

http://technoanswers.blogspot.com/2012/01/ford-f-350-crew-cab-drivers-side-front.html

----------

Car door will not close? http://howtobyme.blogspot.com/2011/11/car-door-will-not-close.html

--------

All power door locks not working? http://howtobyme.blogspot.com/2011/11/all-power-door-locks-not-working-on_14.html

----------

Repairing car Door lock Actuator? http://howtobyme.blogspot.com/2011/11/repairing-car-door-lock-actuator.html --------------- How to Access car door panel? http://howtobyme.blogspot.com/2011/11/how-to-access-car-door-panel.html

---------- Vehicle door panel components?

http://howtobyme.blogspot.com/2011/11/vehicle-door-panel-components.html

--------- Truck Door will not close?

http://schematicsdiagram.blogspot.com/2011/12/ford-truck-door-will-not-close.html

----------- Where is Cars Door control Module located?

http://schematicsdiagram.blogspot.com/2011/12/where-is-cars-door-control-module.html

-------- Power door locks not working?

http://schematicsdiagram.blogspot.com/2011/12/power-door-locks-not-working.html

----------- Door ajar light stays on?

http://technoanswers.blogspot.com/2012/01/door-ajar-light-stays-on.html

---------- Door locks not working?

http://technoanswers.blogspot.com/2012/01/door-locks-not-working-on-ford-explorer.html

---------- Front Door dis-assembly diagram?

http://repairhelpcenter.blogspot.in/2012/02/front-door-dis-assembly-diagram-for.html

--------- Rear Door dis-assembly diagram?

http://repairhelpcenter.blogspot.in/2012/02/rear-door-dis-assembly-diagram-for.html

-------- How to test Power door locks?

http://repairhelpcenter.blogspot.in/2012/02/how-to-test-power-door-locks.html

-------- Doors will not open with Remote?

http://schematicsdiagram.blogspot.in/2012/02/lexus-doors-will-not-open-with-remote.html

--------

How to replace Door Hatch ? http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-hatch-on-acura-integra.html

--------- How to remove Doors?

http://repairhelpcenter.blogspot.com/2011/11/how-to-remove-doors-on-acura-integra.html

-------`- How to Replace Doors? http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-doors-on-audi-a4-and-vw.html

--------

Remote will not unlock Rear door? http://schematicsdiagram.blogspot.com/2011/12/remote-will-not-unlock-rear-door-on-gmc.html

-------- Door locks or windows not working on car? http://schematicsdiagram.blogspot.com/2011/07/door-locks-or-windows-not-working-on.html

---------- Central locking not working?

http://schematicsdiagram.blogspot.in/2012/03/this-is-how-system-operates.html

This will help.

Thanks.

If it flickers at idle, it "might" be engine wear, especially if you are approaching 200,000 miles. It might also be a faulty oil pressure gauge sending unit which is a little more likely.

call Hyundai they will give it to you for a fee

could be bad spark plug. or coil over plug is bad

Without fitting a new bearing to the release fork it is virtually impossible however, i managed to put one together by cutting an inspection hole just big enough to get your hand inside above the slave cylinder and manually meshing the release fork, bearing and spigot shaft simultaneously