20 Most Recent
2003 Jaguar XJ-Series Questions & Answers
Where is the fuel filter located on a Jaguar xj8 2003?
if it is the older xj its at the lh rear over the top of the drive shaft area, if its the later all alluminium xj350 module i think it is under the lh plastic cover that runs down the lh underside towards the front of car, hope this helps.
Programming the garage door opener
Homelink Garage Door Opener Programming Procedure:
The procedure described below was successfully applied to a 2005 Jaguar S-Type.
To begin with, several attempts were made using the programming instructions contained in my Jaguar’s owner’s manual. Though the procedure described in the owner’s manual was straight-forward and understandable, I was unsuccessful in getting the vehicle’s remote to make my garage door opener function. The particular garage door openers I have are both made by Genie. Both openers utilize the “Rolling Code” feature.
To begin with, be sure to clear previous codes on your Jaguar’s garage door opener by first turning (rotating) the ignition key to the “I” position (first notch). Next, simultaneously hold button 1 (left most button) and button 3 (right most button) down until the middle button’s red light changes from continuous on to a rapid flash. This process takes approximately 20-25 seconds. What follows is a two part process. In the first part, get your Genie portable remote and hold it near (approximately 3 inches away from) your Jaguar’s garage door opener console buttons. Choose which button on your Jaguar’s remote you wish to dedicate to your Genie door opener and simultaneously press and hold your Genie opener button and your Jaguar’s opener button. The red light on your Jaguar’s center button (button #2) will light up and within 1-2 seconds will begin to flash rapidly. You have just completed part 1 of the two part process.
Part two: Now it is time to utilize the “Learn” function on your Genie garage door opener. Press the “Learn” button on your Genie garage door opener. The red LED adjacent to the “Learn” button will begin to flash. You now have 30 seconds in which to program your Jaguar’s opener button. Using the same button you just used in the “part 1” procedure, press and hold the same button for several seconds. As before, your Jaguar’s red light in the middle button will light up and within 1-2 seconds, it will flash rapidly. Release the button you are programming. Now, here is the key piece of information! Once again, press and hold that same button. Once again, the center button’s red light will flash rapidly. Release your newly programmed button. This procedure proved successful in my application. Here is what has just happened. The first time you pressed your Jaguar’s remote button tells the Genie opener that it exists and that it is a viable candidate for making your life easier (opening the damn door). The second time you press your Jaguar’s remote button confirms to the Genie’s rolling code that your Jaguar’s signal is legitimate and is to be trusted from then on.
I took my 2003 Jaguar xj8 to get Viper alarm put
Well it is if you want the auto start feature, you need the extra key to clarify the transmission for it to have the auto start feature, but if you want just the alarm you dont need the extra key!
My radio on my jaguar 350 year 2003 is only
You will have to remove the center j shifter trim it pops out...then this will expose two torque head screws ...remove them and also if you have regular rear ac console with chrome guides,remove the vents with a flat tip by starting at the bottom..it will pop out and expose 2 more torque head screws,once they are removed,life the leather console upward and back at the same time and it willslide back and allow you to perform the bottom procedure.
Audio Unit Removal
- Remove the instrument panel console.
- Remove the audio unit.
CAUTION:
- Extreme care must be observed not to damage the high gloss finish on the surface of the audio unit.
- Cleaning of the high gloss finish should only be carried out with a soft dry cloth. Failure to follow this procedure will cause damage to the audio unit facia.
NOTE: Left-hand shown, right-hand similar.
Installation
- To install, reverse the removal procedure.
Abs fault light, engine management light,
try disconnecting the battery both leads and join them together for 5 mins and see what happens cannot find this fault code in teh jaguar OBD codes so consult with teh code reader manufacturers
Not finding what you are looking for?