Hyundai Motor 2002 Elantra - Answered Questions & Fixed issues

Make sure the 3 prongs (2 silver & 1 gold) line up to connect properly when you put it back in. I had to pullout the gold outside of where the bulb sits and slightly pull out the 3 in the actual lens to get a good connection. ***This is what makes the turn signal wireless... They have to be aligned and have contact****

remove the interior door trim and you will see small nuts holding the handle onto the outer door skin. Remove any rods /clips and undo the nuts and the handle will come out.

The best solution you'll get from books at www.reliable-store.com These are books containing info on repair, service, troubleshooting, parts info, assembling dissemble, removal, error/fault codes, wiring diagrams and everything on any vehicles cars, atv, trucks. forklifts, boats, excavators etc

Faulty brake switch.

hyundai elantra If you want to solve your problem, click on the link I attached

If the test says it the issue.. you have no choice but to replace it.. (you could cut it apart and clean it out, then reweld it)..BUT if the inspectors see it,, you are IN BIG TROUBLE!!

you have to mention the make and model that is being tested there are codes but if it is a GM product many scan tools will not read the faults because it requires a scan tool with a special protocol for GM if it is a nissan , the ECM has a small screw that has to be turned to get the codes to read The car is playing so rest assured there are fault codes but who ever is doing the reading is using the wrong scanner or is not familiar with your make of car requirements

Sounds like the fuel pump is starting to go, the problem after fill up is most always related to a failing pump. The other issue may be a dirty throttle valve.

This issue is often caused by the PCV circuit. Check the PCV valve and port for clogging or torn/leaking hoses.

You don't say if you had it checked for DTC's - diagnostic trouble codes ? Have a scan tool that views sensor data hooked up . See what the PCM/ECM or TCM is see for input data . Your best bet mite be to take to a qualified repair shop that has the diagnostic equipment an knowledge to find the problem . Rather then guessing an just replacing parts .

repair manuals have wiring diagrams 1996 2013 Hyundai Elantra Haynes Repair Manual PDF

The code says tps switch so replace the throttle position sensor.

Do you get power to fuel pump relay?

Did you recently clear the trouble codes or disconnect the battery? Once all codes are cleared, the computer will not display systems 'ready' until they go through an evaluation cycle. Some of the systems require a certain number of drive cycles before they will display 'ready'. A drive cycle is usually starting the engine from a cold start (based on coolant temperature) and driving until certain conditions are met. I don't know what the requirements are for your car, but my 2003 pickup truck requires more than 10 drive cycles before it will make the O2 sensors and evaporative emissions 'ready'. Most states only require that a certain number of systems are showing 'ready' to pass emissions certification.

One is under the hood on the drivers side. The other is behind the little tip out tray by the drivers left knee. Open the tray and pull up to remove.

36mm socket and long breaker bar, 12mm and 14mm wrenches and a ball joint separator fork.

Best Manuals to fix your car visit this link

Hi Dani, The links below are two short youtube videos that shows how to fix a car that doesn't start, The 1st link is a car that won't crank over and the 2nd link is a car that cranks over but won't start...CHEERS.. https://www.youtube.com/watch?v=TSE0fOrujW0https://www.youtube.com/watch?v=064Ilsz8Fzg

The VSS sensor is located on the transaxle .
If the VSS is defective replace the instrument cluster

press the helpful button Definition of P0420 is catalyst below threshold. This is indicative of (among other things) a converter that is not working as efficiently as it should be (according to specs). Catalytic converters are not normally a "wear" type item, that is they are not deisgned to wear out and need replacement. If they have failed, it is likely due to something else that caused it to fail. P0447 Evaporative Emission Control System Vent Valve/Solenoid Circuit Open. The Powertrain Control Module (PCM) has detected an open within the circuit that controls the vent valve or solenoid for evaporative emission systems vapor. Read more at: http://www.obd-codes.com/p0447 Copyright OBD-Codes.com http://www.trouble-codes.com/ http://www.obd-codes.com/trouble_codes