Top 20 2004 Infiniti QX56 - Page 4 Questions & Answers

TPMS-Tire pressure monitor sensor. low tire or bad sensor. if your tires are more than 3-5 pounds under pressure, this will trigger the light. Check your driver door for proper tire pressure, air the tires up and drive for 15 mins. If light doesnt go out, check the owners manual for reset procedure.

A P0335 "check engine light" code could be caused by:

• Damaged CKP sensor connector
• Damaged reluctor ring (missing teeth or not turning due to sheared-off keyway)
• Sensor output open
• Sensor output shorted to ground
• Sensor output shorted to voltage
• Failed crank sensor
• Broken timing belt
• Failed PCM

1. Using a scan tool, check if, when engine is running or cranking, that there is an RPM signal.
2. If there is no RPM reading, then visually inspect the crank sensor and connector for any damage and repair as necessary. If there is no visible damage, and you have access to a scope, you could check the CKP 5 Volt square wave pattern. If you do not, then, obtain a resistance reading of your crank sensor from a repair manual. (There are so many different types of crank sensors that there's no way to put here which resistance reading is correct). Then check the resistance of the CKP sensor by disconnecting the sensor and measuring resistance of the sensor. (It is best to check resistance readings from the PCM connector. This rules out any wiring problems from the start. But it does require some mechanical skill and shouldn't be performed if you\'re not familiar with automobile electrical systems). Is the sensor within resistance specs?
3. If not, replace the CKP sensor. If so, recheck resistance reading from the PCM connector. Is the reading still okay?
4. If not, repair open or short in the wiring to the crank sensor and re-check. If the reading is okay, the problem is intermittent or the PCM may be at fault. Try reconnecting and checking for RPM signal again. If there is now an RPM signal, wiggle test the wiring harness to try and induce the fault.

please check this maybe

The answer for fuse should be printed in raised letters on inside of fuse box lid, and in you cars manual.

By this statement I assume you mean your phone is connecting to your car audio system via Bluetooth. If this was a one time event I would say that it could be your network. Again, I assume that this is not just a single occurrence. Try connecting a friends phone to see if the problem persists. If not then it is likely your phone and you can try to get a replacement from your carrier. If you still have the problem with a second phone it is likely the audio system. Check your warranty and seek maintenance from the manufacture.

Battery is weak/dead or bad battery connections. Turn headlights on and turn key. If lights go out or go very dim, that is your problem.

The waring sign ( ! ) is your Tire Pressure Monitoring System (TPMS) Indicator. This means that the computer has detected a difference in tire pressure between your tires of more than 10psi. Look in the owners manual for more information or take it to the dealer. Most cars with TPMS systems require a special tool to reset the light, but you may be able to reset the system by adjusting the tire pressure in all tires including the spare, and driving at more the 15mph for 30 minutes.

The fuel pump is located behind the driver seat on the 2nd row under that seat. You have to cut a piece of the carpet out to get to it. Why I have no idea why Nissan built a vehicle where you have to cut the rug out to get to a part that will need to be replaced one day.

that is a brake warning light. check your brake fluid and make sure it is not low. If it is low you may have a leak somewhere. Look for a puddle under the vehicle. It may also mean time to change brake pads.

If the ! is inside of what looks like a tire it is a low tire pressure warning. Your description could go either way so I wanted to give you both answers

I had the same problem on my 04. Found a used unit on Ebay for $150 and just pulled ou the old one, put in the new one. Appears to work. Do not ahve the manual and am not able to enter in other states (appears to only have addresses for CA?)

https://search.yahoo.com/search?fr2=p%3ads%2cv%3aomn%2cm%3asa%2cbrws%3achrome%2cpos%3a1&fr=mcafee&type=E210US1494G0&p=2003+infinity+m45+blower+relay+location

Did you check for DTC'S ? diagnostic trouble codes .Hook up a scan tool an check live input data to the control module for cruise control? Factory Service Manuals - NICOclub

What colour is the smoke? The easiest way to check this is on first start when the engine is cold. This can give clues as to where the problem could be. is the vehicle doing anything else different? A blue exhaust smoke is commonly oil getting into the cylinders. White smoke suggests coolant getting into the cylinders. Black smoke is the engine running too rich. Blue or white smoke can often mean a blown head gasket. On a 2001 engine that could the most likely reason.

Looks like eBay is the only source. https://www.google.com/search?q=1996+Infiniti+Q45+V8+4.5+air+intake+tube https://www.ebay.ca/itm/313173877626 or these parts https://www.ebay.com/b/Air-Cleaner-Assemblies-for-Infiniti-Q45/43946/bn_1408274 ..

Bettie,Check these sites...https://duckduckgo.com/?t=ffab&q=+CODES+P0014+AND+P0024+ON+2009+INFINITI+FX35+&atb=v159-1&ia=webBest to you.As the one video says check oil level first.

The average cost for an INFINITI Q45 Knock Sensor Replacement is between $954 and $1,055.

INFINITI Q45 Knock Sensor Replacement Cost - RepairPal

The problem is normally all the stuff you have to remove to get to it! https://www.google.com/search?q=infiniti+q45+cost+of+knock+sensor+replacement ..

the service manual covers all that, buy it or rent it? V8 Engine. 1996 Infinity Q45 scans said it bad, if not do not listen to dweebs saying it is bad blind, not told why you want to go there at all.? bank 1, KS-1 they are both mounted to the top of the bare engine block they are Microphones, no loose bolts rattling up there or loose cam chains. the main intake manifold must be pulled. (takes skills) facing engine bank 1 is right bank, cylinder 1 front there. KS1 is on same bank. left word below means drivers seat perspective see below KS1 is on the right facing the engine clear as day we see the intake manifold is gone. FRONT Of car IS HERE X it is big sandwich, remove the top things seen to get here.called gaining ACCESS to it. KS- sensors can lie you (scannned) chain on cam bad. lifter collapsed or worse, can happen, bent valves? do you hear noise (bad) form the engine, even at idle parked. NO MAN CAN GUESS YOUR SKILLS OR TOOLS NOR WHY YOU LANDED HERE, DWEEBS ON THE WWW INTERNET TOLD YOU? but I did answer how. not tools ,just where it is and what must come off. the block. do not break bolts (snap) removing them. I use pen oil and heat and more tactics. ask with 6mm bolts, there, it can be tedious. not wrecking those. now the SM words told (pasted)

1. Properly relieve the fuel system pressure.
2. Disconnect the negative battery cable.
3. Disconnect the air intake duct from the dual duct housing.
4. Unplug the electrical connectors from the throttle body, the step motor AAC valve and the exhaust gas temperature sensor.
5. Disconnect and label the hoses from the valve cover, the throttle body, the step motor AAC valve, the EGR control valve and the air cut valve.
6. If the spark plug wires are in the way, disconnect them and move them aside. Disconnect the accelerator cable from the throttle body.
7. Remove the upper intake manifold collector-to-intake manifold bolts, and lift the assembly from the intake manifold. Discard the gasket.
8. Remove the lower intake manifold collector-to-intake manifold bolts, in sequence, and lift the assembly from the intake manifold. Discard the gasket.
9. If the fuel injector assembly is in the way, perform the following procedures:
   1. Disconnect the electrical connectors from the fuel injectors.
   2. Disconnect the fuel injector assembly from the fuel lines.

1. Remove the fuel rail-to-cylinder head bolts.
2. Remove the fuel rail assembly from the engine.

Remove the intake manifold-to-engine bolts, in sequence, lift the intake manifold from the engine and discard the gasket. see that arrow red, it is inTHERE im told Olive OyL can get there , directly./(grin)

53 lbs

Do you have another key? There could be a problem with the key not being recognized!

Try www.crutchfield.com

How to set the clock in a Infiniti g35? How To Set Your INFINITI's Clock

1. Press the menu button below the lower display.
2. Hit the settings key on the lower display.
3. Locate and hit the "clock" key to adjust "on-screen clock", "daylight savings time", "clock format (24 hr)" and "timezone"

Mar 4, 2019

How To Set Your INFINITI's Clock

https://www.competitioninfiniti.com > Blog Search for: How to set the clock in a Infiniti g35? Videos an well https://www.google.com/search?q=2006+Infiniti+G35+setting+the+analog+clock ..