2002 Hyundai Accent - Page 2 - Answered Questions & Fixed issues

P1586 HYUNDAI - MT/AT Encoding Signal Malfunction https://www.autocodes.com/p1586_hyundai.html

it's called iac solenoid by the throttle

This is a self adjusting hydraulic clutch and it has no adjustment point of any kind.

fuel injector fuel rail on top og egine

Go to the JVC product support site for this.

Have you checked out any videos on youtube ? Check out scanner Danner videos , he's a Tech - Teacher ! Great videos lot of info.

its the same process as bleeding brakes- except you pump the clutch pedal and loosen the clutch slave cylinder located by the front motor mount instead of a brake slave cylinder. what i do is just loosen the slave cylinder bleeder screw and let it all run dry. then disconnect the reservoir from the master cylinder and clean it out with brake cleaner because all that black junk rests in the bottom of that. theres still more in the line, so reattach the reservoir and fill it up. let it bleed all the way back down the line and proceed to pump and bleed the system. if you know how to bleed brakes it should be a piece of cake.

The first thing you must do is have the engine control computer scanned for fault codes, the go from there based on those results.

code p 1402 refers to fuel tank leakage diagnostic module--motor malfunction===causes --fuel tank leakage motor diagnostic module motor code p 1403 refers to the fuel tank diagnostic module ---valve malfunction go to a service dealer and have the unit tested it is possible that by replacing or cleaning the valve section , the problem will be fixed

Code 1402 is a problem with the DMTL motor and 1403 is the circuit for the valve. It involves the fuel tank leak tester. Faulty Diagnostic Module Tank Leakage (DMTL) - Diagnostic Module Tank Leakage harness is open or shorted - Diagnostic Module Tank Leakage circuit poor electrical connection Read more: http://www.autocodes.com/p1403_hyundai.html#ixzz44VrYa4Tf

Yes prb the fuse. Look under the drivers side by the break in the car. It may have a cover over it. They usally have a diagram of what fuse is what. Also under the hood is a bank of fuses. It will be towards the front on either the left or right side under a black cover.

In most cases when the speedometer stopped working Accent Ex went up front bearings and plastic speedometer is broken

Replace the transmission (gear ratio codes are 'absolute')... your transmission is unserviceable.

http://www.hmaservice.com/.. register. Lots of shop manuals, wiring diagrams, etc.

Check the bulbs could be blown low beam

• Defective Vehicle Speed Sensor
• Defective Speedometer
• Vehicle Speed Sensor wiring or connector
• Communication (CAN) bus problems
• Defective transmission or differential Vehicle Speed Sensor drive gear

Disconnect wires to alternator and insert new fuse. If it does not blow then the problem probably lies with the internal diodes in alternator - may have shorted out. If so, replace alternator.

This is very serious and I would advise not driving it AT ALL, until a cause can be identified. Although you said it's "not the front end wobble", it sure sounds like there still is something wrong in the front end and/or the alignment. It could be broken engine mounts, missing hardware/very loose control arms, steering box connections, loose steering column, transmission mounts, driveshaft bearings/mounts or even loose lug nuts on the wheels just to name a few. Please have the car safely raised on jacks and have a mechanic or knowledgeable person look underneath for broken/damaged/missing parts.

SAKHER, VERY DANGEROUS CHECK BRAKE FLUID LEVEL REFILL IF LOW AND TAKE THE CAR TO HYUNDAI DEALER FOR HELP QUICKLY NOT SAFE ISSUE!!!!!!!

Does the car want to pull when sitting still in gear with your foot on the clutch? If so, I would say that your clutch is not fully engaging and could be the cause of your grinding when changing gears. If not then I would think the clutch is operating fully and the synchros are worn and need replaced. But either way, with metalic fluid being in the slave cylinder dust boot, the slave cylinder needs changed.