20 Most Recent
2004 Jeep Liberty - Page 5 Questions & Answers
My jeep Liberty starts fine when the car is cold.
Can't tell you without being there but check the starter relay and all connections at battery, starter and grounds both on engine and fender. Check with a test light or volt meter (Meter is better because it will show power drop off if any) Test with key in run position and in start position as well. Don't forget there is a neutral safety switch that can also fail so check in park and neutral also.
4/5/2015 12:57:59 AM •
2004 Jeep...
•
Answered
on Apr 05, 2015
I have the p0306 code showing for my 2004 3.7
but not one ASE mechanic i bet. they get it right.
so 306 means must misfire.
or better, weak Combustion on #6
so did your mech check compression on #6?
seems not. or vacuum for bouncing, seems not.
that knocking, did he check that first. it must NOT knock.
that knock is serious and will get worse, Id not drive it.
not me, engines are expensive why make it worse?
3/8/2015 3:49:09 PM •
2004 Jeep...
•
Answered
on Mar 08, 2015
2004 jeep liberty won't move when put in gear (like brakes are locked).crank it in neutral put in gear it will go till i touch brakes then won't move again.WHAT'S WRONG WITH THIS THING.
gear, is this a Manual trans? or AUTO you said gear.
what gear, please name the gear, 1,2,3,4,5 R
or PRNDL ( a/t box auto matic) what shift lever selection?
what is out door air temp, you do know brakes can get wet and freeze right?
it wont go you meant? until brakes are touched, key word won't?
ok engine only starts in PRNDL set to N??
is that it?
and then when you shift to D, the car will not move
what about the other gears.? try them all yet?
my guess (wild) is that you dont know how park lock out works.?
that you must hold the brake pedal down to shift to park or neutral.
is that it? (read operators guide?)
my guess is car is not drive-able. key point1 (a dead car)
point 2, engine starts and runs. and races on demand with gas foot.
point 3, im lost. (no trans stated or clear symptoms.)
my jeep has 6speed manual box
and the clutch allows me to start car.
on Automatics trans must be in park or neutral to crank engine.
"it will go till i touch brakes"
I read that 10 times,
my 2nd guess. the engine stalls ?
IS THAT IT, stalls means engine RPM is 0
and right foot actions are dead.
and all dash lamps glow, telling you STALL is now.
2/27/2015 5:27:49 PM •
2004 Jeep...
•
Answered
on Feb 27, 2015
Jeep liberty codes p2302
seen where,? why not tell where seen, we cant guess that.????
- the cluster VFD
- at autozoned?
- or using a real scan tool, BINGO a win and guess what all the other DTCs you missed !!!
2/27/2015 4:13:15 PM •
2004 Jeep...
•
Answered
on Feb 27, 2015
My jeep liberty wonts to start but it wont whats wrong with it
an internal combustion engine needs three conditions present to run. These conditions are compression, ignition, and fuel. A diagnosis of the no start condition involves hunting for these conditions to verify their presence.
Your jeep may be out of gas. The fuel system may be full of stale or watery gas. The fuel pump may have died or the filter or injectors may be clogged. These malfunctions will stop the fuel from reaching the cylinders.
Your jeep may not be getting spark. You may have fouled spark plugs or bad plug wires. Then again, you may have a bad sensor causing no spark.
You may have engine damage. A bad head gasket, fried piston rings, or burnt and bent valves may be killing your compression.
2/21/2015 12:52:52 AM •
2004 Jeep...
•
Answered
on Feb 21, 2015
Not finding what you are looking for?