20 Most Recent 2006 Chrysler Executive - Page 5 Questions & Answers

seen exactly where and how? does car run and drive> or not.\ abs cluster lamp glowing like mad? does cranking the engine sound weak.? if yes battery is weak. does car have secondary battery option/? that is an ABS failure code but is only covered in the service manual

most codes are generic and then their are codes that the manufacturer will have as specific 1391 for a mopar may be different for a toyota or on a ford its a glow plug problem etc --------That code for mopar for the crankshaft position sensor or the CMP sensor once the CKP sensor goes your car wont start at all-----

Based on the information provided, it seems that the issue could be with the actuator or the wiring between the switch and the actuator. The fact that the dash message recognizes the hatch is open when the actuator is in the open position indicates that the sensor is working properly. You may want to check the wiring and connections to ensure that there are no breaks or loose connections. If the wiring appears to be intact, it may be necessary to replace the actuator.

so you replaced the radio ? which is recieving power through the cars existing wiring ?' these modern cars are full of electronics i dont understand , in the fuse board is a computer , called a BCM ? body control unit , which if my muddled theory is correct is full of electronic components , one of which is faulty and affected by the cold , one solution is run a feed direct from the ignition switch to the main power of ther radio , on the radio you will have two feeds , one permamant to hold the memory and then the feed which comes on when you turn radio on , Locate this feed and run a wire direct from ignition side of the switch when on , i think this may cure your problem ,. Yes i know i will be accused of being a cowboy back street mechanic , which iam proud to say i am , But if my theory is correct then my trick should cure the problem , As a kid i had a small radio which done exactly the same thing , It got repaired under warrenty

no car told ,at all just VAN and Chrysler told no VIN, no year ,no van model and worse no engine told (size and cylinder count) dies in Drive and Reverse and low PRNDL not told fuel it burns gasoline ,diesel, LNG, LPG, or? for this failure top cause is low fuel pressure. but we can hear the engine, if misfiring or just bogging bogging is smooth loss of power not violent like walking in a mud swap, smooth. post the vin and we tell you what's under the hood.

The water temperature sensor in a 2002 Chrysler PT Cruiser Dream works by measuring the temperature of the engine's coolant. This information is then sent to the vehicle's Powertrain Control Module (PCM) in the form of an electrical signal. The signal from the water temperature sensor is used by the PCM to regulate the engine's operating temperature by controlling various functions such as the engine's air/fuel ratio, ignition timing, and the operation of the radiator fan. The wire that sends the signal from the water temperature sensor to the PCM is typically a two-wire sensor. One wire is used to supply power to the sensor, while the other wire carries the signal back to the PCM. The wire that carries the signal is usually the wire with a different color or a stripe on it. However, it is best to consult the vehicle's wiring diagram to confirm the exact wire.

THE COOLANT SYSTEM ON MOST CARS ARE VERY COMPLEX,. NOT IN THEORY EVER, BUT IN PRACTICES SO MANY PLACES TO LEAK. 1996 NO VIN TOLD OR WHAT ENGINE IS THERE,. USA CAR HAD 2. 3.3 L EGA V6 3.5 L EGE V6 FEW USEFUL FACTS TOLD. JUST LEAKS. THERE ARE 2 WAYS TO FIND IT AND YOU DID NONE.(i SAY STOP GUESSING, (BUT CAP AND THERMOSTAT ARE SLAM DUNKS.) 1: HOT ENGINE TEST, HAS 15PSI UNDER THE CAP AND ANY LEAKS , HOOD UP IS SEEN CLEAR AS DAY EVEN SQUIRTS 3 FEET AWAY FOOLING YOU. DO NOT DRIVE THE CAR AND BLOW WATER ALL OVER THE ENGINE BAY OR OVER HEAT IT. NOT TOLD IS COOLANT ON THE GROUND OR IN THE OIL PAN OR ON PASSENGERS FOOT WELL OR TOES.OUCH. 2; USE AND READ LEAK DOWN PRESSURE TOOL. DONE COLD. ENGINE AND 10 X MORE SAFE BUT THE TOOL COSTS MONEY TO BE SAFER. #1 TOLD AGAIN BY ME HERE VAST TIMES. FIRST GET THE Rad FULL. NEW GAS CAP $5 NO 27 YEAR OLD THERMOSTAT IS GOOD. EVER. 7 YEAR EOL DESIGN LIFE SPAN IS SPEC. SO ....A>>>>>$25 FIX, AND NO CAR FIX IS FREE.. (ASIDE OF LOSE CLAMPS) KEYOFF COLD ,RAD, ADD 50% AF FLUID FULL i USE "PRESTONE ANY CAR" AF FLUID TODAY. ZERO MIX ISSUEA WITH OTHER BRANDS !!!!!!!! OK RAD IS FULL. FOR SURE. HOOD UP. ENGINE COLD KEY ON START IT FOR UP TO 30 MINS. GET ENGINE FULLY HOT,. NO NOT BOILING KEY OFF IF IT OVERHEATS TOO SOON KEY OFF NOW. i USE SCAN TOOL AND SEE PID ECT AT 180F+ NOW AND SAY OK THIS BLOCK IS NOW FULLY HOT. (NORMAL) THE CAP NOW IS AT 15-PSI AND IN FACT ANY LEAKS THERE ARE MOSTLY ARE SEEN NOW IF YOU GO SLOW AND JUST LOOK. THE HOSES ALL THE WHOLE ENGINE CAN LEAK WATER PUMP HEADS TO BLOCK LEAKS(HEAD GASKETS0 IF V6/8 ENGINE, NONE TOLD CAN LIKE AT INTAKE MANIFOLD FRONT OR REAR (PUSH ROD ENGINES NOT OVERHEAD CAM ENGINES WATER IN TO THE ENGINE OIL PAN OR THE TRANNY. WATER TO PASSENGER FEET HEATER CORE BAD. LEADS TO GROUND ARE EASY TO FIND, LOOKING TO OIL PANS WE SEE LUBE AS CHOCOLATE MILK. THE FRONT OF MY 3.7 LITER , THE FRONT COVER OF ENGINE, HAS WATER PATHS. THAT SURE CAN LEAK. THE CAR RUNNING WATER FOR COOLANT AND IT FREEZES OUT SIDE AT JUST BELOW 32F THE ENGINE CRACKS IN HALF. CRACKED BLOCK AND OR HEADS. DOOMED, SO NEVER JUST WATER ONLY RUN 50% AF ONLY THE TRICK IS WATCH IT LEAK HOOD UP. HURRY NOT. YOU WILL SEE IT OR IS A HUGE PROBLEM. OR IS HEATER CORE LEAKING OR SEE RAD LEAK LIKE MAD. FIND THE LEAK PARKED IS BEST. GOOD LUCK !!!

Throttle position sensors are mounted to the side of the throttle plate and measure the position of the throttle - essentially, how far down the gas pedal is pressed

Question edited to what I think you meant. Info here. Basically 'year make model fuse box diagram' will find it. https://www.google.com/search?q=chrysler+202+change+headlight+relay ..

Chances are your fuel pump needs to be replaced, try some starter fluid to see if you have a fuel problem.

you dont have one

no VIN told no Engine told and is an engine question. a Gen 4 car. 2 engine, not told which, 3.3 or 3.8L V6 1684 means low battery so you cranked the battery too low. so charge the battery back up./ 1388 is ASD relay drop out. it can drop out for many reasons, one is lost park,. why do fuel first ever, but not test all spark first.?fuel can not burn if spark is wrong dead or timed wrong. most folks putting a new distributor in , do it wrong./ sorry, not done all this by the service manual 3.3 L V6 there is no distributor on the 3.3L at all, yes a huge coil pack NOT wired wrong, do he HV wires 1 b y1, never ever all at once unless you mark each for firing orderthe coil pack HV wire see is no good this old yes replace those.1 by 1, never all pulled at once.. or oops 3.8 same thing there is no distributor in this car ever. so is must be a confusion,, huge coil pack, named wrong sure. most posters here posting put the coil pack in wrong.funny how the land here, no? if you did that wrong, (pack wires) then now you must learn the firing order. or it will not run. ever. the better coils are marked like this,3.8. rearL513R L246R front if one spark wire or plug is open circuit 2 cylinders are dead.they are wired wasted spark using 3 coils for 6.hope the new crank sensor was installed by the book or oops 2 3,8 the firing order, is 123456 per this. more info sure, ASD is not simple.USA ANSWER FOR SURE NOT UK, THAT IS DIFFERENT.ASD 101, what makes the ASD DROP?)lots)THE PCM SEES SOME ERRORS AND DROPs ITEVEN THE 8VDC POWER BUS TO SENSORS LOST(SHORTS)COIL hV SPARK PRIMARY ERRORS,? SEEN?or A SHORTED INJECTOR.CMP OR CKP SENSOR ERRORS. or 8vdc dead.SENTRY KEY IMMO MODULE(skim) FAILING, IS THE IMMO LAMP THERE AND GLOWING WRONG OR BAD KEYTRY THE 2ND GOOD KEY THE CAR CAME WITH NEW?LOST THE 2ND KEY?SKIM IT IS CALLED SAME AS MY JEEPs..USE A REAL SCAN TOOL, NOt OLD ONE FROM 1996YES EVEN THE ASD TEST FAILING SHUTS ITSELF DOWN. IF OUTPUT IS DEAD a ASD, IT JUST SHUTS DOWN.(TO NOT HAVE FUEL FIRE IS WHY)A BAD ASD RELAY/ sure.ASD DROPS IF SPARK IS DETECTED BAD (IN ALL WAYS) THIS FEATURE IS TO CUT FUEL AND NOT HAVE FUEL FIRE FOR SURE SPARK DEAD.WE DON'T WHAT RAW FUEL DRIPPING FROM EXHAUST PORT THAT BE SUPER SUPER BAD, AND WE HAVE SEEN IT.(some horrific)how?THE immo SKIM MODULE ,(SAY a BAD KEY)SENDS a serial message (PCI_bus) to pcm and ecmtells the pcm for sure to cut fuel in 2seconds flat. (a clue)chapter 3, immo lamp 13immo page in your users guideDuring normal operation, the Theft Alarm/Immobilizer Light will come on for three (3) secondsimmediately after the ignition switch is turned on for abulb check. Afterwards, if the bulb remains on, thisindicates a problem with the electronics.If the bulb begins to flash after the bulb check, thisindicates that an invalid key has been used to start thevehicle. Both of these conditions will result in the enginebeing shut off after two (2) seconds of running.Keep in mind that a key which has not been programmedis also considered an invalid key even if it is cut to fit theignition lock cylinder for that vehicle.do not have both keys inside car same timethe 2 that came with car new.here is the IMMO skim lamp lucky 13most folks tend to forget is there unril NOW

This is Fixya and we don't message anyone. Also not a good idea to post your phone number to the 11 MILLION viewers of this site which is also frequented by a million marketing scammers!What type of key code? The cutting code? Just go to an auto locksmith. They can use an impressioning tool or get access to the records.

The most common reason for oil and water mixing is a blown head gasket. This can also cause a low coolant level that can affect the heaters on the vehicle. It could also be worth checking the coolant thermostat as that is also a common reason for overheating.

Typically, with what you are describing is a shift solenoid. Can usually be replaced without too much hassel. They are located in the transmission case. I have not worked on your type of vehicle, but if you take off the tansmission fluid pan, they should be right up there.

To change the motor mount driver's side of a 2004 Chrysler PT Cruiser, you will need to follow these steps:

1. Raise the vehicle: Use a jack to raise the vehicle off the ground and support it with jack stands. Make sure the vehicle is securely supported before proceeding.
2. Locate the motor mount: The motor mount is located on the driver's side of the engine compartment, between the engine and the frame of the vehicle.
3. Disconnect the negative battery cable: This will help prevent any electrical issues while working on the vehicle.
4. Remove the engine mount bolts: The motor mount is held in place by bolts that attach it to the engine and the frame. Using a socket wrench, remove these bolts.
5. Remove the old motor mount: With the bolts removed, the old motor mount should come loose. Carefully lift it out of the engine compartment.
6. Install the new motor mount: Place the new motor mount in position and align the bolt holes. Insert the bolts and tighten them to the manufacturer's specified torque.
7. Reinstall the battery cable: Reconnect the negative battery cable and test the engine mount for proper operation.
8. Lower the vehicle: Carefully lower the vehicle to the ground and test drive the vehicle to ensure everything is working correctly.

It's important to keep in mind that this is a general guide and the steps may vary depending on the specific model and year of your vehicle. It's best to consult the vehicle's service manual or seek the help of a professional technician. It's also important to use the right tools and safety equipment, such as gloves, safety glasses, and jack stands. Also, it's important to note that changing a motor mount can be a difficult task and it's best to have a professional technician perform the repair.

Fuel gauge drops to emptyChrysler Minivan

means using wrong old and lame scan tools p0700 means transmission error GENERAL( uSA fed code) means others are there but not using 2008 or newer scan tools means missing all those better DTC errors get the car scanned in a real shop using real tools no kidding. missing p17xx codes and more.

ck here...... https://www.fixya.com/cars/t25177057-location_fuel_filter_2006_chysler