20 Most Recent 1994 Mercury Villager - Page 9 Questions & Answers

FOLLOW THE LOWER RADIATOR HOSE.IT WILL TAKE YOU RIGHT TO WATER PUMP.

get a test light turn key on check it you have fonud the hot for the ing turn the key on like u are starting it u will find the other hot

Look under the hood, usually a belt diagram on the emissions sticker (look near the top of the radiator).

any speed?? when it does work, do all the speeds work? if so, you will need to replace the fan motor.

there are several connections to clean. First try cleaning the 2 small connections on the positive battery post. Hen we can go from there if it doens't fix it.

go here for villager help

http://groups.yahoo.com/group/villagerquest/

obtainable from a local parts store or even the local library ....maby even wiki it via internet

the pump motor likely is bad. get a used washer fluid reservoir at a pick n pull yourself or at car-part.com. page with * is lowest cost.

Pump and Reservoir, Windshield Washer Removal

1. Disconnect the battery ground cable (14301).
   
2. Raise and support the vehicle.
   
3. Remove the RH wheel (1007).
   
4. Remove the RH front fender splash shield (16103). Refer to Section 01-02 for the removal procedure.
   
5. Remove the windshield washer reservoir top bolt.
   
   
6. Disconnect the windshield washer reservoir fluid level sensor electrical connector.
   
7. Disconnect the rear window washer pump electrical connector from the rear window washer pump.
   
8. Disconnect the windshield washer pump electrical connector from the windshield washer pump (17664).
   
9. Place a suitable drain pan under the windshield washer reservoir (17618) and drain the washer fluid.
   
10. NOTE: The rear window washer hose end is color-coded, matching the connector on the rear window washer pump. Match the colors to ensure proper installation.
    
    Disconnect the washer hoses from the windshield washer pump and the rear window washer pump on the windshield washer reservoir.
    
    
11. Loosen the two windshield washer reservoir side bolts.
    
12. Remove the windshield washer reservoir by sliding it out of the side slots.
    
13. Remove the windshield washer pump.
    
    Installation

To install, reverse the removal procedure. Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).

in front of the cabin fan.

have the linkage on the transmission checked and the transmission fluid level

If you can turn the pump pulley by hand, likely it's OK... If so, change the belt. if not, you know what you need to do.

they are the same Nissan 3.0L engine in Villagers and QUests. Get reman on ebay for under $200. Why replaciing?

Go here for expert Villager help.

http://autos.groups.yahoo.com/group/villagerquest/

if it is a intank pump that is what it should be replaced with.

have you checked the level of oil in the power steering? check it while the vehicle is running. and then add fluid accordingly

The shifter is not fully in park or neutral beacuse it's loose. Check for a small screw on the floor on the driver side.
If not adjusted properly, the stater won't engage.

here's a pic to help. This view looking up under steering column.

go to this site for mre help from our villager group.
http://autos.groups.yahoo.com/group/villagerquest/

look in files and photos

seats use heavy corrent & use relays instead of fuses. check relays in fuse panel. see chart on cover or owner manual for location.

Also, this is for 96 villager seats.

Circuit Protection
Power is supplied to the seat motors through the 30A POWER WINDOW fuse. The fuse is located in the LH engine compartment fuse junction panel and is hot at all times. The circuit breaker is behind the interior fuse junction panel and prevents current overload and component damage.

go to this site for more help

http://autos.groups.yahoo.com/group/villagerquest/

you have fuses there and in the van by the drivers side instrument panel.

here's how to change,
Fuse — Main Fuse Junction Panel NOTE: The MAIN and ALT fuses are high ampere cartridges that are held in place by screws, which must be removed in order to replace the cartridge. For removal of the MAIN or ALT fuse, refer to the procedure in this section. Always replace a blown fuse with a new one having the same amperage rating.

Removal

1. Remove the appropriate fuse panel cover (14A003).
   

1. Pull the fuse straight up from the fuse junction panel (14A068). If the fuse is a cartridge-type, carefully pry the clip, then pull the fuse straight up.
   

I would also check relays, including inhibtor relay. relas have a relese tab.


Item Part Number Description 1 14N089 RAD FAN — LO (Low FC Relay) 2 14N089 RAD FAN — HI 1 (High Fan Control [ FC] Relay) 3 14N089 RAD FAN — HI 2 (High FC Relay) 4 14526 PWR WDW 5 14526 ABS (Anti-Lock Brake System) 6 14526 RAD FAN 7 14526 FRT BLWR (Front Blower Motor) 8 14526 MAIN 9 14526 RR DEF (Rear Defroster) 10 14526 ALT (Generator) 11 14526 IGN SW (Ignition Switch) 12 — Joint Connector 13 14526 H/L RH (RH Headlamp) 14 14526 H/L LH (LH Headlamp) 15 14526 ALT (Generator) 16 14526 ENG CONT (Engine Controls) 17 14526 INJ (Injectors) 18 — SEC (Smart Entry Control) 19 — Hoodlamp 20 14526 ABS (Anti-Lock Brake System) 21 14526 HORN (Horn Speed Control) 22 14526 Fuel Pump (PCM) 23 14N089 ASCD Hold (Speed Control Relay) 24 14N089 Bulb Check 25 14N089 Headlamp, RH 26 14N089 INHIBIT (Throttle Position [TP] Switch) 27 9P704 FUEL PUMP 28 14N089 HORN
check 11, 16, 17, 22, 26, 27

hi, i think your heater motor is faulty this is a common problem on mercs, hope this helps

Try cleaning the throttle body.

Resetting it will not help, as the ECM (Electronic control module will readjust thus same issue. If the engine is running sluggish at a very low idle, but fine when the RMP is increased, it is probally the pcv valve, actually the hose part that goes into the back of your Carb., check this by spraying starting fluid, ether, towards the back of fuel intake while running at idle, if it revs, Bingo! Be very carefull not to start a fire, and keep an extinguisher handy!!!

try this quick
while trying to turn the key turn the steering wheel back and forth
sometime it binds the key switch
if that doesnt work let me know you have deeper problems
good luck
paul