20 Most Recent 2006 Chrysler Sebring - Page 9 Questions & Answers

0helpful
1answer

Heater will blow cold air randomly

Are the hoses going to the heater core hot. you can findv the 2 hoses under the hood ,and back of the motor. you may also have a sticking blend door
10/31/2012 12:13:27 PM • 2006 Chrysler... • Answered on Oct 31, 2012
0helpful
1answer

Where is the fuel filter on a 2003 chrysler sebring located?

Get underneath the vehicle. You will find the fuel filter on the trunk end of the fuel tank, up towards where the top of the fuel tank meets the bottom of the vehicle body. The bottom is flat and smooth and it is the largest thing underneath your vehicle. The fuel filter is a gray metal canister about the size of a small can of soup, but a little bit fatter. It will have a rubber tube coming out of each end.
10/16/2012 3:29:48 PM • 2006 Chrysler... • Answered on Oct 16, 2012
0helpful
1answer

Cable broke on driver side rear window regulator for 2006 chrysler sebring convertible window won't go up. can the cable just be replaced?

As far as i know, yes. just go to a crysler dealership and get them to order it for you.
10/9/2012 7:04:49 PM • 2006 Chrysler... • Answered on Oct 09, 2012
0helpful
1answer

How do I get to the drivers side light bulb in a

I will assume you are talking about the headlight?!

Removal
CAUTION: do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced life will result.

1) Disconnect and isolate negative battery cable.
2) Remove headlamp unit retaining screws. (bolts)
3) Remove headlamp unit to expose back of unit.
4) Disconnect wire connector from back of headlamp bulb.
5) Rotate retaining ring counterclockwise.
6) Remove retaining ring.
7) Pull headlamp bulb and remove from headlamp unit.

Installation

1) Install headlamp bulb to the headlamp unit.
2) Install headlamp bulb retaining ring.
3) Rotate retaining ring clockwise.
4) Connect wire connector to bulb.
5) Install headlamp unit.
6) Install headlamp retaining screws. (bolts)
7) Connect the battery negative cable.

More detailed info on how to get unit out.

Removal

1) Disconnect and isolate the battery negative cable.
2) Remove the two retaining screws.
3) Remove the upper fascia retainers by prying under the head of the fasteners with a flat bladed tool.
4) Remove headlamp unit from fender side first, then pull headlamp unit out.
5) Disconnect the wiring harness from the bulbs.
6) Remove the headlamp unit.

Installation

1) Connect wire harness to the bulbs.
2) Install headlamp unit.
3) Install the retaining screws.
4) Install upper fascia retainers.
5) Connect the battery negative cable.

I hope this will help you to get the light changed.
10/7/2012 2:43:31 AM • 2006 Chrysler... • Answered on Oct 07, 2012
0helpful
1answer

My car turn on light of batery after that motor light and then gas light

Please explain in greater detail
9/24/2012 9:12:56 PM • 2006 Chrysler... • Answered on Sep 24, 2012
0helpful
1answer

My car turn on light of batery after that motor light and then gas light and so it is broke

You need to explain in more detail when, where, how, due to, etc. Of your problem.
9/24/2012 6:34:05 AM • 2006 Chrysler... • Answered on Sep 24, 2012
0helpful
2answers

Rad fan fuse blows out when low speed fan kicks on...

Sounds like you need to replace the fan motor
8/9/2012 5:01:17 AM • 2006 Chrysler... • Answered on Aug 09, 2012
0helpful
1answer

2006 chrysler sebering motor squeals when ac on

loose or bad belt. replace or tighten belt.
8/2/2012 11:20:29 PM • 2006 Chrysler... • Answered on Aug 02, 2012
0helpful
1answer

Car reves up, and does not respond when pressing gas

If it revs up, the gas pedal works. Is the check engine light on ?
8/2/2012 8:16:32 PM • 2006 Chrysler... • Answered on Aug 02, 2012
0helpful
1answer

The hood latch is brock and I cant open the hood

if you can see your lock assembly through the grille, then you have a good chance og opening your hood, the lock assembly had a cable attached to it, i used a long handle screw driver and popped mine open, also did you try taking a pair of vise grips and locking them on the cable from the inside of the vehicle and pulling with a little force, that should open her right up. Good luck.
7/28/2012 12:30:07 AM • 2006 Chrysler... • Answered on Jul 28, 2012
0helpful
1answer

When I go over 75 in my 06 Chrysler Sebring my car makes a thudding noise.

Pretty much all vehicle diagnostic work, is from30 MPH to 60 MPHI have no idea why anyone would attemp to drive70 or more.
7/27/2012 11:36:20 PM • 2006 Chrysler... • Answered on Jul 27, 2012
0helpful
1answer

2006 sebring car will cut out at 2200 rpm

To recap, it sounds like low fuel pressure, so I would get the fuel pressure checked.
7/26/2012 1:57:06 PM • 2006 Chrysler... • Answered on Jul 26, 2012
0helpful
1answer

2006 sebring cut out at 2200

It could be the fuel filter, bad gas over a period of time, it could be a number of things. Try an additive called Seafoam, you can buy it at any auto parts store. Pour the whole bottle into your tank before you fill up and see if that helps. Maybe you have crude build up. It usually is from using cheap gas but I don't know a time frame of ownership of your car.
7/21/2012 7:23:26 AM • 2006 Chrysler... • Answered on Jul 21, 2012
Not finding what you are looking for?

730 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Chrysler Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Sebring Chrysler

  • Sebring Chrysler

Most Popular Question

expansion valve 06 chry sebring conv

  • Cars & Trucks
Loading...