20 Most Recent 1999 Chrysler Concorde Questions & Answers


There's a website that has all this information about all this and manuals everything totally free t here are many actually but I personally like few like reliable-store .. let me know if u need help
thanks

1999 Chrysler... | Answered on Mar 06, 2019


Removal & Installation
To Remove:


  1. Before servicing the vehicle, refer to the precautions at the beginning of
    this section.
  2. Release fuel pressure.
  3. Remove or disconnect the following:

    • The rear seat





      Electrical Connector
      dod_intrpd_fuel__tank_elec_conn.gif



    • The fuel pump electrical connector





      Battery Cable
      dod_intrpd_batt_conn.gif



    • Battery cable

  4. Raise and safely support the vehicle
  5. Remove or disconnect the following:





    Fuel Tank Drain
    dod_intrpd_fuel_tank_drain.gif




    • Fuel from fuel tank





      Stabilizer Bar
      dod_intrpd_stab_bar.gif








      Stabilizer Bar and EVAP Canister
      dod_intrpd_evap_cann.gif



    • The rear stabilizer bar brackets from body
    • Stabilizer bar toward rear of vehicle





      Fuel Filler Tube
      dod_intrpd_filler_tube.gif



    • The fuel filler tube from fuel tank





      Fuel And EVAP Lines
      dod_intrpd_fuel_evap_lines.gif



    • Fuel and EVAP lines

  6. Position transmission jack under fuel tank assembly.
  7. Remove fuel tank straps bolts passenger side first.
  8. Lower fuel tank and remove the purge line and vent line.
  9. Disconnect fuel line from fuel pump module by depressing quick connect
    retainers with thumb and fore finger.
  10. Slide fuel pump module electrical connector lock to unlock.
  11. Disconnect the electrical connection from the fuel pump module, by pushing
    down on connector retainer and pulling connector off of module.





    Fuel Tank Locknut
    dod_intrpd_fuel_tank_tool__nut.gif



  12. Use Special Tool # 6856 to remove fuel pump module locknut.
  13. Remove fuel pump and O-ring seal from tank. Discard old seal.

To Install:


  1. Wipe seal area of tank clean and place a new seal in position in the tank
    opening.





    Fuel Tank Locator
    dod_intrpd_fuel_pump_loctr.gif



  2. Position fuel pump in the tank.

    • Make sure the alignment tabs on the underside of the fuel pump module flange
      sits in the notches on the fuel tank.

  3. Position the locknut over the fuel pump module.
  4. Tighten the locknut using Special Tool # 6856

    • Torque to: 40.5 ft. lbs. (55 Nm)

    CAUTION
    Over tightening the pump lock ring may
    result in a leak.

  5. Position the fuel tank on the transmission stand.
  6. Install or connect the following:

    • Fuel pump electrical connector into hole in the body
    • The purge and vent lines
    • Fuel tank and tank straps
    • The fuel filler tube and tighten the clamp
    • The stabilizer bar and install bolts

  7. Lower vehicle.
  8. Install or connect the following:

    • The fuel pump electrical connector that is in the rear seat
    • The rear seat
    • The battery cable

  9. Fill fuel tank.
  10. Use the DRB or equivalent scan tool to pressurize the fuel system.
  11. Check for leaks.


prev.gif next.gif

1999 Chrysler... | Answered on Sep 27, 2018


The center dash speaker wires are:
PNK/RED (+) and PNK/BLK (-).

1999 Chrysler... | Answered on Mar 28, 2018


The cam position and crank position sensors need to be checked. A diagnostic test will determine the exact problem

1999 Chrysler... | Answered on Jul 28, 2017


I went to the Concorde forum and saw what other owners said. Captain mody said, "There is a black case in the middle of the upper part that contain fuse #5 red 10amp you need to replace this fuse by another on and after that every thing will work again" Another guy named Chris said: "Open your driver's door and open the fuse box on the left, there's a handle near the door hinge. This is most likely a blown fuse - check the fuse box lid for the diagram. Find out which one is blown and swap it out. Not a $400!!!" Site is: http://www.topix.com/forum/autos/chrysler-sebring/TL00F443HJC4T92RR I hope this helps you out!

1999 Chrysler... | Answered on Apr 01, 2017


see dealer. most of them will give u that

1999 Chrysler... | Answered on Nov 06, 2016


This is most likely being caused by a defective air temperature control blend door and or actuator. This part moves back and forth deep inside the HVAC ducting to divert air across the Heater core or the AC Evaporator core, when they fail or stick they can create this issue.

1999 Chrysler... | Answered on Oct 12, 2016


Your best bet would be to take it to AAMCO or some other repair shop an have them run diagnostics on the car . They could hook up scanner an be able to tell you right away , instead of replacing parts you don't need .

1999 Chrysler... | Answered on May 27, 2016

Not finding what you are looking for?
1999 Chrysler Concorde Logo

661 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Concorde Chrysler

  • Concorde Chrysler

Most Popular Question

1999 chrysler concorde factory amplifier

  • Cars & Trucks
Loading...