20 Most Recent 2006 Isuzu I 370 Questions & Answers

normally it is stamped on the engine block near the cylinder heads but on block side.

As listed in the owners manual.

Weight of the Trailer
How heavy can a trailer safely be?
It depends on how you plan to use your rig. For
example, speed, altitude, road grades, outside
temperature and how much your vehicle is used to
pull a trailer are all important. It can also depend
on any special equipment that you have on
your vehicle, and the amount of tongue weight the
vehicle can carry. See “Weight of the Trailer
Tongue” later in this section for more information.
Maximum trailer weight is calculated assuming
only the driver is in the tow vehicle and it has all
the required trailering equipment. The weight
of additional optional equipment, passengers and
cargo in the tow vehicle must be subtracted
from the maximum trailer weight.
The following charts show how much your trailer
can weigh, based upon your vehicle model
and options.
2WD Extended Cab Axle Ratio Maximum Trailer Weight GCWR*
Automatic Transmission,
2.9 L Engine 3.73 3,100 lbs (1 406 kg) 7,000 lbs (3 175 kg)
Manual Transmission,
2.9L Engine 3.73 2,100 lbs (952 kg) 6,000 lbs (2 721 kg)
4WD Crew Cab Axle Ratio Maximum Trailer Weight GCWR*
Automatic Transmission,
3.7L Engine 3.73 4,000 lbs (1 814 kg) 9,000 lbs (4 082 kg)
*The Gross Combination Weight Rating (GCWR) is the total allowable weight of the completely loaded
vehicle and trailer including any passengers, cargo, equipment and conversions. The GCWR for your
vehicle should not be exceeded.

Me and my wife thinking about buying the
2007 Isuzu I-370
I don’t know if this model performance well someone here ca give *** his though

Run a jumper wire from the battery directly to the wiper motor leads, if the motor works than your relay is bad.

dead or weak, glow plugs.

hsa means HILL START AID. hsa is standard on isuzu's npr and nqr models fitted with manual transmission. hsa maintain truck-brake pressure until the clutch is engaged and limit vehicle roll-back. it is very effective for take-off on hills under load condition.

I currently work in a large truck shop. I have been hunting the net for pictures of your Torque rods and can not find any. If you post picture here I can tell you how to take them apart to replace the bushings.

Hera are some V-10 firing order diagrams.

if you use the wrong oil viscosity will have trouble starting isuzu
oil switch in them has to have pressure up before she will open solenoid let fuel in
make sure proper oil was fitted

Your light switch controls those items, it may be defective.

One has to check the fuse for Instruments. When it failed you check any cable for wear marks and the chance it shorted out against some ground. Next the main plugs for power to be in good condition and not being corroded. Sometimes the cables break where they are clamped on a cable lug and one can then easily pull them out of a connector. It can be a bad connection to ground, where ground cables connect to a larger wire. Ignition switches can fail and have connections for many functions with plugs down below. It should be any of these causes.

Have you had it plugged into an OBD scanner to check it isn't a sensor causing the issue? Sometimes something else can trigger a "No Start" issue like a bad sensor or a faulty immobiliser. The two most likely reasons for the starter to do that is - 1. a weak or flat battery or - 2. A bad starter motor. Check the battery is fully charged, (somewhere around 12.6 to 13.2 volts). If the battery is good it is more likely to be the starter motor. On a 2001 model it mght be the original factory starter. They do wear out and fail especially on high mileage or high compression engines like diesels. That 'Click' noise is probably the Solenoid switch on the starter working but the motor isn't turning like it should.