2000 Ford Windstar - Answered Questions & Fixed issues


I never had this problem myself, what's your reset switch might have gone bad

2000 Ford... | Answered on Jan 03, 2020 | 74 views


Camber is not adjustable. If it is out of alignment, you probably have other parts that are bent or weak. Take to an alignment shop for diagnosis of the camber.

2000 Ford... | Answered on Apr 16, 2019 | 144 views


There are two relay's located in the under hood fuse / relay box . Windshield wiper on / off relay an windshield wiper speed relay .Both relay's are controlled by the FEM - front electronic module . The prudent thing to do would be to take to a qualified repair shop that has a professional type scan tool to check for DTC'S - diagnostic trouble codes rather then play a guessing game . Changing parts that don't fix the problem . The wiper switch is a input to the ( FEM ) when an input is seen the (FEM) then energizes the relay's .

2000 Ford... | Answered on Mar 04, 2019 | 552 views


The blinking THEFT indicator is telling you that anti-theft is enabled when your Windstar is shut down. That's normal in your Windstar. Mine too.

2000 Ford... | Answered on Oct 28, 2018 | 47 views


My friend is a part time mechanic he gets his solutions from www.reliable-store.com
he gets from their every single detailed info, instructions etc. on ner's, operations, maintenance etc.
U can get help from there
there is a girl at chat she can help you

2000 Ford... | Answered on Jul 04, 2018 | 241 views


If the fuel pump is original, it could be time to replace but also consider the possibility of spontaneous ECM failure.

2000 Ford... | Answered on May 11, 2018 | 86 views


with the help of service and repair manual with diagram you can solve your problem easily and you can get the manual from the given link http://toolsnyou.com/

2000 Ford... | Answered on May 08, 2018 | 53 views


The "reversing lamps" as Ford calls them are located at the bottom of the rear light assemblies - not in the lift gate. When your Windstar is shifted into reverse, output from the PCM is applied to the rear electronics module (REM) to ground the lamps and turn them on. In short, if you need + 12 volts to turn on the camera, you will have to find it elsewhere. This is a common problem encountered when trying to install cameras in older cars.

2000 Ford... | Answered on Dec 23, 2018 | 168 views


My friend is a part time mechanic he gets his
solutions from www.reliable-store.com he gets from their every single detailed info, instructions, wiring/electrical/fuse diagrams, error codes, torque specs, troubleshooting, transmission etc. everything on all vehicles, and manuals like service, repairs, parts, owner's, operations, maintenance etc.
U can get help from there
there is a girl at chat she can help you

2000 Ford... | Answered on Jun 25, 2018 | 94 views


The battery is failing

2000 Ford... | Answered on Jan 19, 2018 | 167 views


Air/Fuel/Spark.
To clean a fuel filter you replace it. you can take the injectors off and soak them in cleaner as well but if it will not turn over, you are not getting the starter to work which could be the starter or could be the solenoid that is between the batter and the starter.
If it is turning over, take out a spark plug and hold it firmly to the engine case and crank one revolution to verify your spark plugs are firing. Don't get shocked (not my fault if you do). You should also smell the gas coming from the cylinder and that will help confirm the injectors and fuel system are working.
Hope that helps.

2000 Ford... | Answered on Jan 15, 2018 | 225 views


Definitely. The specified harness adapter you used makes no provision for connecting the rear seat control unit. You may be able to modify the adapter wiring to connect to the rear speakers.

2000 Ford... | Answered on Jan 14, 2018 | 108 views


I would need to hear this.

2000 Ford... | Answered on Jan 06, 2018 | 198 views


If the light is on, codes are stored. Get the codes read. Don't ask us to guess

2000 Ford... | Answered on Jan 01, 2018 | 59 views


sounds like the timing belt is off.

2000 Ford... | Answered on Jan 01, 2018 | 65 views


Open the driver door and check the wiring between the driver door and the body (inside the rubber protector) which leads to the fuse box. It may be old and brittle or just broken. Re solder the wire and protect with electrical tape if broken.

2000 Ford... | Answered on Dec 12, 2017 | 158 views


Ford trucks have known issue with faulty instrument displays printed circuit boards.

2000 Ford... | Answered on Nov 09, 2017 | 53 views


Sounds like your brake calibers are sticking. Get new ones and new pads. You probably should get new rotors also because with the dragging calibers they most likely got hot and are warped. Search on ebay and www.rockauto.com . I personally use power stop drilled and slotted rotors with mid grade pads. You can probably get a whole kit.

2000 Ford... | Answered on Oct 22, 2017 | 75 views


Look at your motor mounts ( very likely), a bad tire on the driver's side, or perhaps a worn strut or some other worn out suspension part.
God bless your efforts.

2000 Ford... | Answered on Sep 07, 2017 | 92 views


The transmission pump can whine when worn out . The fluid can become aerated and cause a whining sound .

2000 Ford... | Answered on Aug 21, 2017 | 102 views

Not finding what you are looking for?
2000 Ford Windstar Logo

2,289 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

1998 Ford Windstar
1998 Ford Windstar

1,797 Questions

2001 Ford Windstar
2001 Ford Windstar

1,796 Questions

1999 Ford Windstar
1999 Ford Windstar

1,174 Questions

2003 Ford Windstar
2003 Ford Windstar

996 Questions

1996 Ford Windstar
1996 Ford Windstar

582 Questions

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...