20 Most Recent 2004 Ford GT Questions & Answers

Fuse.. or relay fuse.. either under the Hood or under the dash.

replace the speed sensor and rerun the fault codes as this unit may be restricting the engine operation and put it in limp mode.

for the front and rear lights to stop working together along with the wiper motor indicates a faulty earth connection between the body and the chassis Check and clean all earth wires between the engine ,body and chassis panels

split intercooler hose, happened to mine do you hear a sucking noise when accelerating? new hose costs about 40 quid main dealer only

www.fgoc.co.uk

i think you can spray it with a hose and get it real clean and you gotta put oil over it. go to your auto parts store or online and find your oil

I have a Gran Torino also and the best place to find that answer is at the Library reference section ( those books can't be checked out so there complete) just copy what you need, there located were they have all the older car repair manual. I once worked at the library part time so I know well. Those old school manual had everything you needed very detailed section by section. Unlike chiltons books today for civilian use they have nothing at all.

You may have a faulty circuit in the instrament panel assembly, only further testing would prove or disprove my theory?

chk your fuses

check drain tubes or hose under car may be cloged

Check the fuse or the brake light switch.

SECTION 205-02B: Rear Drive Axle/Differential — Ford 8.8-Inch Ring Gear 2003 Mustang Workshop Manual IN-VEHICLE REPAIR Axle Shaft Removal

1. Raise and support the vehicle. For additional information, refer to Section 100-02 .

1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .

1. Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .

1. Remove the differential housing cover (4033) and drain the lubricant. For additional information, refer to Differential Housing Cover in this section.

1. Remove the differential pinion shaft (4211).
   1. Remove the differential pinion shaft lock bolt (4241).
   1. Remove the differential pinion shaft.

1. CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
   Remove the U-washer (4N237).
   1. Push the axle shafts (4234) inboard.
   1. Remove the U-washer.

1. CAUTION: Damage to the rear brake anti-lock sensor (2C190) may occur if it is not removed before the axle shaft.
   Carefully remove the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .

1. CAUTION: Do not damage the wheel bearing oil seal.
   Remove the axle shaft.

--------------------------------------------------------------------------------------
Rear Wheel Bearing and Axle Shaft Oil Seal Removal

1. Remove the axle shaft (4234). For additional information, refer to Axle Shaft in this section.

1. NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged.
   Using the special tools, remove the rear wheel bearing and wheel bearing oil seal.

Installation

1. Lubricate the new rear wheel bearing with the specified lubricant.

1. Using the special tools, install the new rear wheel bearing.

1. Lubricate the lip of the new wheel bearing oil seal.
   • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.

1. Using the special tools, install the new wheel bearing oil seal.

1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.

-------------------------------------------------------------------
Installation

1. Lubricate the lip of the wheel bearing oil seal
   • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.

1. CAUTION: Do not damage the wheel bearing oil seal.
   Install the two axle shafts.

1. CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
   Install the U-washer.
   1. Position the two U-washers on the button end of the axle shaft.
   1. Pull the axle shaft outward.

1. NOTE: If a new pinion shaft lock bolt is unavailable, coat the threads with Threadlock and Sealer EOAZ-19554-AA or equivalent meeting Ford specification WSK-M2G351-A5 prior to installation.
   Install the differential pinion shaft.
   1. Align the hole in the differential pinion shaft with the case lock bolt hole.
   1. Install a new differential pinion shaft lock bolt.

1. Install the differential housing cover and fill the rear axle with the specified lubrication. For additional information, refer to Differential Housing Cover in this section.

1. Install the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .

1. Install the rear brakes. For additional information, refer to Section 206-04 .

1. Install the tire and wheel assembly. For additional information, refer to Section 204-04 .

1. Lower the vehicle.

WIRING DIAGRAM FOR 12N TYPE 7-PIN Black socket or plug
for vehicle road lights
Colour Terminal Purpose Looking at the Socket towards the plug.
Looking at the Plug towards the socket. Yellow 1 (L) LH Indicator Blue 2 (54G) Rear Fog Light (or Aux.) White 3 (31) Earth Green 4 (R) RH Indicator Brown 5 (58R) RH side Light Red 6 (54) Stop Lights Black 7 (58L) LH Side Light

the abs switch could be going bad or the relay for it could be weak.the relay is under the hood.have it checked taking care of one problem could solve the other