20 Most Recent 1997 Ford Probe Questions & Answers


The transmission is just old and tired. Time for a rebuild or a newer car.

1997 Ford Probe | Answered on Feb 05, 2015


First I will change the spark plugs, My BA Ford in Australia was like that, totally different car with new spark plugs

1997 Ford Probe | Answered on Jan 04, 2014


4th post, i answered #1 of the 4.
or join a ford probe forum
or go to alldata.com and look for your self,as i did for you in post1.
you failed to state the engine options, so the answer is near impossible. I answer for them all.....

1997 Ford Probe | Answered on Oct 16, 2013


Try unhooking the positive battery cable for about ten minutes. This will reset the cpu and place it into limp mode. As you drive the computer relearns your driving habit and chances are you will never notice the difference. often when electronic parts are changed the computer does not recognize the new part, but will on reboot.

1997 Ford Probe | Answered on Oct 16, 2013


Could be the fuel pump relay or the check valve in the pump, and the throttle position sensor could be worn out.

1997 Ford Probe | Answered on Sep 01, 2013


chain

1997 Ford Probe | Answered on Aug 15, 2013


NO. the vacuum is used to make the brake pedal easy to push, power brakes. the pedal would be hard without vacuum, that is why the pedal gets hard with the key off and engine not running. the problem you are having is more of a hydraulic problem.
Have the brakes checked asap. the brake system may have a leak causing the pedal to go low. check the fluid level and if it is low or empty then there is a problem, could be a rotted brake line leaking or a wheel cylinder leaking.

1997 Ford Probe | Answered on Jul 02, 2013


I think the module is under the dash on the passenger side behind
the kick panel in front of the door.

1997 Ford Probe | Answered on Jul 02, 2012


if u can get the frt end off the ground. Both sides. Leave car in netural. Put your hand on the strut spring above wheel . Spin tire at the same time . See if you can feel any virbration with your hand on the coil spring. If so and hear some roaring noise. Thats it be carefull for car not to fall on you or pinch your hand.

1997 Ford Probe | Answered on Jun 16, 2012


This can be the result of various problems that lead to your fuel mixture being to rich, however a common one for late 90's model vehicles would be a bad O2 sensor, this is also a problem that typically doesn't set off your check engine light but is reported to your cars computer. Best advice would be to take it to the nearest auto-part store such as Autozone and have them check your cars for any reported OBD2 codes, this is a service most part stores provide for free and will give you a good place to start.

1997 Ford Probe | Answered on May 16, 2012


Belts aren't made like that. A new belt doesn't have a right and wrong way, it just goes on. But once it has been installed and run, then you don't want to take it off and reverse it-always put a used belt on to run the same way as it was taken off. So unless it was a used belt, no it can't be put on backward.

1997 Ford Probe | Answered on May 09, 2012

Not finding what you are looking for?
1997 Ford Probe Logo

138 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

1993 Ford Probe
1993 Ford Probe

-59 Questions

1994 Ford Probe
1994 Ford Probe

211 Questions

1995 Ford Probe
1995 Ford Probe

-51 Questions

1996 Ford Probe
1996 Ford Probe

-60 Questions

1990 Ford Probe
1990 Ford Probe

85 Questions

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Probe Ford

  • Probe Ford

Most Popular Question

anyone help me please seat alhambra

  • Cars & Trucks
Loading...