1983 Ford Mustang Hatchback - Page 4 - Answered Questions & Fixed issues
Location of r f crash sensor on 2005 mustang
Many Fords don't have crash sensors up front, they opted to incorporate the sensors into the control module. Check with Ford to be sure. I hope this helps. Take care. If you have more questions for me use testimonial. Thanks
2/12/2019 1:06:14 AM •
Ford Mustang...
•
Answered
on Feb 12, 2019
•
180 views
1998 cobra, no start, and no injector pulse!!?? I.have spark, fuel pressure, starts with starting fluid only, checked for reference volts on pcm and it was good, I have @12volts to the injectors, but noid light doesn't light, so no communication to the injectors!!??...
Or bad ground, try cleaning ground connections on fire wall
2/5/2019 2:09:27 AM •
Ford Mustang...
•
Answered
on Feb 05, 2019
•
187 views
Where is the turn signal flasher located on a 2005 mustang gt?
Does not use a flasher , controlled by SJB - smart junction box , module - computer etc...
Turn Signal and Hazard Lamps
All turn signal outputs are controlled by the SJB. The multifunction switch and the hazard switch are hard-wired to the SJB. When the multifunction switch is in the left or right turn position, or the hazard switch is engaged, the SJB processes this information and outputs the appropriate command to the turn signal and hazard lamps. All turn signal lamps provide a lamp outage indication.
Rather then trying to guess your way to a repair , Take it to a qualified repair shop. Could have DTC'S - diagnostic trouble code's stored that point in the correct diagnostic path .
Inspection and Verification
- Verify the customer concern.
- Visually inspect the following for obvious signs of mechanical or electrical damage.
Visual Inspection Chart
Mechanical
Electrical
- Multifunction switch
- Hazard switch
- Circuitry
- Bulbs
- Smart junction box (SJB)
- If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
- If the cause is not visually evident, connect the diagnostic tool to the data link connector (DLC) and select the vehicle to be tested from the diagnostic tool menu. If the diagnostic tool does not communicate with the vehicle:
- check that the program card is correctly installed.
- check the connections to the vehicle.
- check the ignition switch position.
- If the diagnostic tool still does not communicate with the vehicle, refer to the diagnostic tool operating manual.
- Carry out the diagnostic tool data link test. If the diagnostic tool responds with:
- CAN circuit fault; all electronic control units no response/not equipped, refer to Section 418-00 .
- No response/not equipped for SJB, refer to Section 419-10 .
- System passed, retrieve and record the continuous diagnostic trouble codes (DTCs), erase the continuous DTCs and carry out the self-test diagnostics for the SJB.
- If the DTCs retrieved are related to the concern, go to the Smart Junction Box (SJB) Diagnostic Trouble Code (DTC) Index.
- If no DTCs related to the concern are retrieved, GO to Symptom Chart .
-
Smart Junction Box (SJB) Diagnostic Trouble Code (DTC) Index
DTC
Description
Action
B1342
ECU is Faulted
CLEAR the DTCs. RETRIEVE the DTCs. If DTC B1342 is retrieved again, INSTALL a new SJB. REFER to Section 419-10 . TEST the system for normal operation.
B1499
Lamp Turn Signal Left Circuit Failure
Go To Pinpoint Test K .
B1501
Lamp Turn Signal Left Circuit Short to Battery
Go To Pinpoint Test K .
B1503
Lamp Turn Signal Right Circuit Failure
Go To Pinpoint Test K .
B1505
Lamp Turn Signal Right Circuit Short to Battery
Go To Pinpoint Test K .
B2048
Left Rear Turn Lamp Circuit Short to Ground
REFER to Stoplamps in this section to continue diagnosis.
B2049
Left Rear Turn Lamp Circuit Open
REFER to Stoplamps in this section to continue diagnosis.
B2050
Right Rear Turn Lamp Circuit Short to Ground
REFER to Stoplamps in this section to continue diagnosis.
B2051
Right Rear Turn Lamp Circuit Open
REFER to Stoplamps in this section to continue diagnosis.
B2071
Hazard Switch Signal Short to Ground
If the hazard lamps are inoperative, Go To Pinpoint Test L .
If the hazard lamps are always on, Go To Pinpoint Test M .
B2281
Right Turn Switch Short to Ground
Go To Pinpoint Test J .
B2282
Left Turn Switch Short to Ground
Go To Pinpoint Test J .
B2529
Left Rear Turn Lamp Circuit Failure
REFER to Stoplamps in this section to continue diagnosis.
All other DTCs
-
REFER to Section 419-10 .
12/22/2018 6:16:37 PM •
Ford Mustang...
•
Answered
on Dec 22, 2018
•
679 views
94 mustang 5.0 run to min then cut off.fuel pump work find, replace coil still will not run. what could be worng?
no idea without a look and threaten it with my magic hammer but in all seriousness on the fuel rail is pressure regulator although its often called a fuel dampener if this is faulty a fault like you describe can occur.Best advice i can offer from afar is to ask a local mechanic to have a look for you ,sorry this is not a magic fixya quick type answer but as stated without vehicle in front of me this is one of them faults that could need a bit more investigating .
12/7/2018 4:39:06 PM •
Ford Mustang...
•
Answered
on Dec 07, 2018
•
75 views
Where is the fuel pressure sensor located o 2003 mustang
There are 2 one is on the fuel rail on top of the manifold where the injectors are the other is on top of the gas tank if your having problems filling the gas tank it's this one if your car's not starting it's the fuel rail 4.6?maybe go to
rockauto.Com and look up your vehicle then the part and you'll see what it looks like ok good luck stephen
11/25/2018 11:21:19 AM •
Ford Mustang...
•
Answered
on Nov 25, 2018
•
114 views
Not finding what you are looking for?