1997 Ford Crown Victoria - Page 9 - Answered Questions & Fixed issues


you can go to autozone.com and register for full free online repair manual or go to google ebooks and view free chilton's manual

1997 Ford Crown... | Answered on Oct 23, 2009 | 128 views


I would repalce the fuel filter, air filter and the sparkplugs. Check the boots at the plugs for holes burned through by the spark plug high voltage. It would be helpful to know the mileage of this vehicle.

1997 Ford Crown... | Answered on Oct 23, 2009 | 150 views


nothing to lubricate suspension wise. there are chassis points that can be lubed. look for grease nipples in the undercarriage, front end mostly

1997 Ford Crown... | Answered on Oct 18, 2009 | 295 views


Lap belt or shoulder harness? Lap belt - remove rear seat bottom by pushing in on bottom edge of the seat cushion and lifting. This will expose the lap belt and its anchor. Shoulder belt should be accessible via trunk compartment. If not then you'll have to remove the back of the rear seat to get to it.

1997 Ford Crown... | Answered on Oct 14, 2009 | 342 views


Sedans
  1. Remove the screw(s) and wing nut retainers at the rear of the luggage compartment and push the trim away from the back of the light.
  2. Remove the wing nuts retaining the light assembly to the vehicle and the retaining nut from either side of the luggage compartment and pull the light body assembly from the vehicle.
  3. Turn the bulb socket(s) counterclockwise to the stop and remove the socket(s) from the light assembly. Remove the bulb(s) from the socket(s).
  4. Installation is the reverse of the removal procedure.
56c16fa.gif
Push the trim away from the back of the light—1992-98 Crown Victoria

f147c29.gif
The rear tailamp assembly is held by various fasteners

da5bd90.gif
Remove the wing nuts retaining the light assembly to the lower back panel—1992-98 Crown Victoria

e896b59.gif
Remove the nut retaining the light assembly from the side of the luggage compartment

2e1520f.gif
Pull the light assembly away from the vehicle—1992-98 Crown Victoria

1997 Ford Crown... | Answered on Oct 12, 2009 | 1,056 views


3 Engines available all 3 here full diagrams
http://www.p71interceptor.com/firingorder/

Rate me plz : )

1997 Ford Crown... | Answered on Oct 01, 2009 | 839 views


Also check to see if there is power in the start wire form the ignition switch, the wire is a white wire with pink stripe, most likely not a common problem, but still something that could go wrong. this wire will feed the starter relay under the hood...

1997 Ford Crown... | Answered on Sep 23, 2009 | 620 views


is this recline power operated?

1997 Ford Crown... | Answered on Sep 14, 2009 | 498 views


with the aid of a test light you can determine this first are all the fuses good if so prop a length of wood or if someone is handy there to work the brake , test the wire until power is found then repair as necessary .but check the fuses first as well as the brake pedal switch and ensure it is reaching when the brake pedal is applied

1997 Ford Crown... | Answered on Sep 07, 2009 | 362 views


You need a new multi function switch IE wipers high/low beam headlights, Your next clue will be no low beam headlights when needed


1997 Ford Crown... | Answered on Mar 27, 2010 | 452 views


Separate mudula all together, your car may or may not be set up with the wiring ( factory wiring ) to install the system. Have your local Ford dealer run the VIN # to check.

1997 Ford Crown... | Answered on Jul 27, 2009 | 129 views


no it is nit

1997 Ford Crown... | Answered on Jul 21, 2009 | 105 views


it doesn't appear to have a fuse, so it is probably the swith on the dash or the controlunit next to the latch in the trunk!!

1997 Ford Crown... | Answered on Jun 17, 2009 | 130 views


did you replace and/or resurface the rotors??
a warped rotor will cause vibration and/or pulsating in the pedal!!
fuse # 16 is for cigar lighter/ flasher relays!!

1997 Ford Crown... | Answered on Jun 17, 2009 | 239 views


Blend door actuator. When it fails for some reason it turns to the hot side and gets stuck. Dash must come out. I usually do it in 3 hours, because I've done it numerous times.

1997 Ford Crown... | Answered on Jun 17, 2009 | 885 views


have the multifunction switch checked and the flasher.

1997 Ford Crown... | Answered on Jun 15, 2009 | 371 views


have them check all hoses and the condenser pump for leaks, plus all the electrical connections for the AC. it may just be old age for your air conditioning.

1997 Ford Crown... | Answered on Jun 11, 2009 | 80 views


Burning oil, or antifreeze. or running too rich, not enough air.

1997 Ford Crown... | Answered on Jun 04, 2009 | 92 views


if you have unit i think you have look for 2 holes 1/8 inch in dia on both sides take a coat hanger and cut 2 12 inch lengths and bend into semi circles and insert into holes firmly and it will slide out if not have a friend pull on the radio while you push on your new ford radio tools

1997 Ford Crown... | Answered on May 28, 2009 | 198 views


There should be a safety trunk release located on the upper rear window deck platform- a black handpull . If it is still intact- it should pop the trunk lid.

1997 Ford Crown... | Answered on May 27, 2009 | 632 views

Not finding what you are looking for?
1997 Ford Crown Victoria Logo

393 questions posted

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...