1996 Ford Mustang - Answered Questions & Fixed issues
How to fix a cluct fork in a 96 ford mustang
Did you check your fluid level? If this is on a Borg Warner World Class T5 transmission the check/fill hole will be on the passenger side of the transmission. Unscrew the bolt and check. Fluid should be even with bolt hole. If not fill it with ATF. Yes they use ATF. Fill it up to bolt hole(fill it til you spill it) and replace bolt.
12/8/2017 3:58:21 AM •
1996 Ford...
•
Answered
on Dec 08, 2017
•
70 views
Relay on 96 mustang
I am not sure exactly what your question is, but the relays in your mustang are located on either the under hood fuse box or the CCRM, which is located in the passenger side fenderwell. To do a bench test on one to see if its working, simply locate the relay in question and unplug it.Look on it's side and you will see its schematic with numbers at either end of two symbols. One symbol will be a straight line with a circle at either end and the other will be a circle with a line running from it at 45 degrees with a circle underneath it when that line ends.
Get two wires and attach one to your cars battery positive and negative terminals. The pins on the bottom of the relay are numbered. Match the 2 pins that match the numbers for the symbol with the straight line with a circle at each end(numbers will be next to the circles) and touch one wire to one pin and the other wire to the other pin. You should hear an audible click. If you do then the relay is good, if not the relay is bad.
11/20/2017 11:53:59 AM •
1996 Ford...
•
Answered
on Nov 20, 2017
•
348 views
The tail light assy is a 3 bulb on a 1996 mustang
This is the only diagram I could find for tail-lamps. The top wires are voltage, the bottom wire is ground. The brown color wire is voltage for tail lamps. The other color wire is turn or stop, depending. The turn and lower brake lites use the same bulb filament, just not at the same time. The lower brake lites are wired through turn signal switch. I don't know if diagram matches what you have? I looked at several, all showed the same thing.
8/13/2017 7:42:02 PM •
1996 Ford...
•
Answered
on Aug 13, 2017
•
128 views
Ford mustang clutch
did you pack the thrust bearing with grease before fitting. its always best to pack with grease before fitting. as new bearing only come with a small amount for testing the bearing, pack grease into the bearing and spin it do this fa few times and wipe away the excess off before fitting.
7/3/2017 6:34:05 PM •
1996 Ford...
•
Answered
on Jul 03, 2017
•
90 views
I put a 1996 4.6 engine and ecu wiring into a
Since it sounds like you also carried over the OBD2 connector, do you have access to an OBD2 scan tool with datastream mode? If so, you should be able to monitor various sensors to see if that offers a clue as to why it stalls. When it just spins over have you checked for spark, fuel, and injector pulse width?
5/2/2017 10:17:05 PM •
1996 Ford...
•
Answered
on May 02, 2017
•
69 views
Alternator not charging battery
What is the output voltage of the alternator with all the lights on and the heater blower on high and the engine at 1500 RPM?
4/26/2017 8:23:31 PM •
1996 Ford...
•
Answered
on Apr 26, 2017
•
114 views
How do you adjust an electronic clutch on a 96 Mustang GT 4.6 L V8
There is no such thing as an electronic clutch. Assuming your talking about the clutch associated with the transmission. The clutch is engaged via a cable going from the clutch itself to the clutch pedal through the firewall. There is also a clutch quadrant under the dash (attached to the pedal) that is self adjusting. If this goes bad then you need to replace it. What is the issue your experiencing?
4/8/2015 9:39:17 PM •
1996 Ford...
•
Answered
on Apr 08, 2015
•
237 views
How do u reset a security system on a 96 ford mustang
Try disconnecting both battery terminals, Wait about 30 minutes. Touch both terminals together +/- , Be sure not to touch battery while touching both hot -n- ground together for a few seconds. Then put the hot/red cable back on the battery-tighten. Then put on the ground to the - side of battery. Start your car- push brake pedal to the floor push lock/unlock button. and see if it worked. If not replace battery in key fob. make sure you put hot to the hot side/ and ground to the ground side of battery!!!!.
3/31/2015 6:17:32 PM •
1996 Ford...
•
Answered
on Mar 31, 2015
•
210 views
How too put my top down on my 1996 ford mustang
The car must be put in park or neutral and the emergency brake applied before you push the power button to lower it. It's a safety feature to prevent people from trying to open or close them while in motion.
3/24/2015 2:47:36 PM •
1996 Ford...
•
Answered
on Mar 24, 2015
•
130 views
Not finding what you are looking for?