Top 20 1993 Ford Crown Victoria Questions & Answers

It is missing a spring on that rod.

The bubbling is just the air being removed by fluid, no problem. the foaming is just the pump action, no problem. As for the leakage, remove the pitman arm and replace the seal on shaft the pitman arm is bolted to. If you still have leakage, replace the seal in the top of the box where the column bolts to the box for it's just running down the box and looking like the leak is from the bottom seal.

It's more then likely a problem with the lighting control module ! View a wiring diagram at http://www.bbbind.com/free_tsb.html Google location of LCM to see where it lives .

I have owned a 1991 Grand Marquis. Very similar vehicle. Fuel filters, mass airflow sensor (cleaning constantly, finally replaced with OEM part...do not use cheap auto parts store junk on this part), and a tune up. These also have the two coil packs, which do have problems, and I replaced these after the problem resurfaced over time. There are l\also many sensors that affect the computer...camshaft, crankshaft, temperature, etc. The problem with a 1993 vehicle is the OBD I , not OBD II reader is needed. These never really show you what is wrong, only where to possible start checking

Generally head lights and dimmer switches are two different things. It seems like you have ashort in your circuit somewhere. I would remove the lens covering of your headlights and check to make sure you have strong connections. Make sure you do not touch any of the contacts because your battery is still connected. Also make sure your hands and body parts are clear from the fan. Even though your car is turned off, the fan can come on by it self. Best.

The serpentine belt, located in the front of the engine compartment on the front of the engine, has either come off or broken. In that case, you may need another belt. Or the idler pulley has gone bad. Look, using the aid of a flashlight if necessary, for a pulley that is loose. Good Luck!

First find the 2 coolant hoses that lead to the firewall in the engine bay. Disconnect both hoses from the engine. You need to force fluid through the "inlet" hose which is usually on top of the engine(I think it leads to the water pump). Monitor the fluid that comes out... If you're having heater issues, you will probably see a bunch of gunk come out. Flush it out until it runs clear. You can also flush both ways if you're not sure which one is the inlet. You can also try just running regular coolant flush that you can find at most department stores and parts stores, through the motor, following the directions.

If its dark color it is likely rear main seal on engine. If it is red color it is front seal on transmission. check fluid levels, overfilling engine oil or transmission fluid can cause this also. both require major removal of tyranny etc. If you never done this get qualified help. .

It's located under the car on the passenger (right) side between the front tire and door area.

possible spark control module ,will it idel at all fuel pressure regulator

remove the wheel, remove the spindle dust cover and remove tho cotter pin and remove brake caliper and finally remove thr spindle nut,washer and inner bearing and finally the rotor. remove the dudt seal on the back of the rotor and finally the inner braeings.when you replace the bearings make sure that you replace the races and install a new seal on the rotor

I'm thinking they were hub Assembly's ... If that's the case then remove tire Axle nut Caliper bracket, rotor Andfew bolts holding hub on...

Pull the knob off and the retainer nut should be in behind.

check speed sensor

Take it to the dealer, there is nothing you can do.

Listen to the engine, if the noise is down low it is rod if it is up high it is valves. IF it is rod knock it will eventually throw the rod.

I replaced mine last November. Do you need to know all the steps or do you have a specific question?

A/C system is low on refrigerant .Charge A/C ,checking for leaks, Also IdleAir motor may be wearing out.

check the park neutral switch for proper operation

It willo follow the ruts in the road like a tram or a train thats obvious