20 Most Recent 1993 Ford Crown Victoria Questions & Answers


I have owned a 1991 Grand Marquis. Very similar vehicle. Fuel filters, mass airflow sensor (cleaning constantly, finally replaced with OEM part...do not use cheap auto parts store junk on this part), and a tune up. These also have the two coil packs, which do have problems, and I replaced these after the problem resurfaced over time. There are l\also many sensors that affect the computer...camshaft, crankshaft, temperature, etc.

The problem with a 1993 vehicle is the OBD I , not OBD II reader is needed. These never really show you what is wrong, only where to possible start checking

1993 Ford Crown... | Answered on Nov 19, 2018


It is missing a spring on that rod.

1993 Ford Crown... | Answered on Oct 08, 2018


The bubbling is just the air being removed by fluid, no problem. the foaming is just the pump action, no problem. As for the leakage, remove the pitman arm and replace the seal on shaft the pitman arm is bolted to. If you still have leakage, replace the seal in the top of the box where the column bolts to the box for it's just running down the box and looking like the leak is from the bottom seal.

1993 Ford Crown... | Answered on Sep 03, 2017


15A FUSE 4 in the I/P fuse panel is for the dome lamp and radio. 15A FUSE 16 and 10A FUSE 6 also apply to the radio as well as the 25A AUDIO FUSE in the engine compartment fuse box.

1993 Ford Crown... | Answered on Feb 23, 2017


fuel pump may be located in the gas tank

1993 Ford Crown... | Answered on Feb 12, 2017


It's more then likely a problem with the lighting control module ! View a wiring diagram at http://www.bbbind.com/free_tsb.html Google location of LCM to see where it lives .

1993 Ford Crown... | Answered on Jan 13, 2017


Before you get into this involved job I have a few suggestions. First is the pump leaking causing the system to lose coolant. Grab the fan and try to move it from side to side to see if there is play. Next when was the last time the thermostat was changed out. The thermostat can be stuck in a way as to restrict water flow. Another cause of over heating is a clogged radiator. Older cars can have a slug build up in the radiator core causing a significant cooling lose.
Water pumps on a Crown Vic is located on the front of the engine behind the fan. You should really get a service manual as there are a lot of steps in this job that must be done correctly to avoid future problems.
You start by draining the entire cooling system by opening up the drain plug on the bottom of the radiator. This antifreeze must be disposed of properly by taking it to a repair shop for pick up. Next remove the fan guard followed by disconnecting all the belts. Some people remove the radiator to gain working room. before removing the radiator disconnect the lower hose and the upper hose to the engine. The transmission oil cooling lines are next. Now remove all the bolts holding the radiator in place. As you can see this is not a job for a novas. If you are not mechanically inclined this could be a nightmare of a job.

1993 Ford Crown... | Answered on Apr 05, 2016


Generally head lights and dimmer switches are two different things. It seems like you have ashort in your circuit somewhere. I would remove the lens covering of your headlights and check to make sure you have strong connections. Make sure you do not touch any of the contacts because your battery is still connected.
Also make sure your hands and body parts are clear from the fan. Even though your car is turned off, the fan can come on by it self.
Best.

1993 Ford Crown... | Answered on Feb 04, 2015


The serpentine belt, located in the front of the engine compartment on the front of the engine, has either come off or broken. In that case, you may need another belt. Or the idler pulley has gone bad. Look, using the aid of a flashlight if necessary, for a pulley that is loose. Good Luck!

1993 Ford Crown... | Answered on Dec 06, 2014


sounds to me like you could have damaged the oil pump, running low on oil can cause numerous things to fail.. possibly spun the rod bearings and they are beating on the crank. I wouldn't start it, but if the noise is in the bottom I would drop the oil pan.

1993 Ford Crown... | Answered on Oct 12, 2014


First find the 2 coolant hoses that lead to the firewall in the engine bay. Disconnect both hoses from the engine. You need to force fluid through the "inlet" hose which is usually on top of the engine(I think it leads to the water pump). Monitor the fluid that comes out... If you're having heater issues, you will probably see a bunch of gunk come out. Flush it out until it runs clear. You can also flush both ways if you're not sure which one is the inlet.

You can also try just running regular coolant flush that you can find at most department stores and parts stores, through the motor, following the directions.

1993 Ford Crown... | Answered on Oct 07, 2014


possible spark control module ,will it idel at all fuel pressure regulator

1993 Ford Crown... | Answered on Oct 02, 2014


Your fuel pump may not be working properly

1993 Ford Crown... | Answered on Sep 30, 2014


If its dark color it is likely rear main seal on engine. If it is red color it is front seal on transmission. check fluid levels, overfilling engine oil or transmission fluid can cause this also. both require major removal of tyranny etc. If you never done this get qualified help. .

1993 Ford Crown... | Answered on Sep 17, 2014


remove the wheel, remove the spindle dust cover and remove tho cotter pin and remove brake caliper and finally remove thr spindle nut,washer and inner bearing and finally the rotor. remove the dudt seal on the back of the rotor and finally the inner braeings.when you replace the bearings make sure that you replace the races and install a new seal on the rotor

1993 Ford Crown... | Answered on Sep 13, 2014


I'm thinking they were hub Assembly's ...
If that's the case then remove tire
Axle nut
Caliper bracket, rotor
Andfew bolts holding hub on...

1993 Ford Crown... | Answered on Sep 03, 2014

Not finding what you are looking for?
1993 Ford Crown Victoria Logo

355 questions posted

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Crown Victoria Ford

  • Crown Victoria Ford

Most Popular Question

93 crown victory lx leaking fluid from

  • Cars & Trucks
Loading...