20 Most Recent 2003 Dodge Ram Maxi Questions & Answers


It should be on the fire wall !

2003 Dodge Ram... | Answered on Nov 05, 2016


The heads can crack almost anywhere.

2003 Dodge Ram... | Answered on Apr 25, 2016


sometimes turning the ignition on 3 times quickly without starting will reset the computer. If the van has power locks and keyless entry then try using only the keyless entry. Sometimes your car wont have a alarm but an anti theft device which will not allow it to start if it goes off or something triggers it.

2003 Dodge Ram... | Answered on May 02, 2014


sound like its flooding

2003 Dodge Ram... | Answered on Jan 26, 2014


Is the check engine light on ?

2003 Dodge Ram... | Answered on Sep 27, 2013


sounds like a crank positioning sensor

2003 Dodge Ram... | Answered on Apr 15, 2013


1.did you install the right ball joints? double check that.depends on gvw
2.worn out tapers in knuckles
3. did the new ball joints come with washers to put under the nuts to get the castle nuts in the right spot and did you use them?
4.is it the joint that is moving or the stud? Was it a cheap ball joint? and did you have the correct tool to install the joints ie a press and sometime a funny socket for the uppers if they are threded in?

2003 Dodge Ram... | Answered on Mar 27, 2013


Eight...

2003 Dodge RAM 1500 5.7 liter Hemi V-8 VIN "D"

zjlimited_0.gif

Dont forgetted rate this answerr. Good luck.

2003 Dodge Ram... | Answered on Jan 21, 2013


Not sure about your dodge, but on hondas there is a lever under the driver side vent to allow fresh(outside air) when its cold out, it will be cold, even with the heat on inside, so check to see if your has that lever somewhere on that side...hope that helps

2003 Dodge Ram... | Answered on Jan 21, 2013


your glows plugs not working. check glow plug relay or fuse.

2003 Dodge Ram... | Answered on Apr 27, 2012


P0300 is a random engine cylinder misfire occurring in all cylinders of the engine, it is non specific. This can be a programming problem with the powertrain control module (PCM) or a problem such as dirty fuel injectors or engine vacuum leaks in the intake gaskets, poor state of tune or worn engine parts like piston rings or valves. A bad tank of fuel can also cause this. You never mention the engine you have so my advice is general in nature and based on my 30 years as a tech..

2003 Dodge Ram... | Answered on Jan 03, 2012


P0132 is O2 sensor High circuit sensor voltage sensor 1 bank1, What this mean is either you 02 sensor on bank1 (or where cylinder 1 is located) is disconnected internally or extenally you will need to inspect the harness for any disconnection if connection is good then you will need a new 02 sensor

2003 Dodge Ram... | Answered on Nov 03, 2011


A code P0440 could mean one or more of the following has happened:

  • The gas cap is not installed or working properly
  • The purge solenoid has failed
  • The canister is plugged and not working properly

2003 Dodge Ram... | Answered on Mar 30, 2011

Not finding what you are looking for?
2003 Dodge Ram Maxi Logo

93 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

1999 Dodge Ram
1999 Dodge Ram

1,750 Questions

1994 Dodge Ram
1994 Dodge Ram

192 Questions

2004 Dodge Ram
2004 Dodge Ram

170 Questions

1998 Dodge Ram
1998 Dodge Ram

139 Questions

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Ram Dodge

  • Ram Dodge

Most Popular Question

dodge 2003 code po300

  • Cars & Trucks
Loading...