1999 Ford F350 Regular Cab - Answered Questions & Fixed issues
I have a 1999 ford f-350 that sounds like its
Injector pump seals most likely.
If they have never been changed,CHANGE THEM NOW!
One is HARD to change,make sure they change that one too and not just the easy ones.
2nd most common leak there is the return fuel lines between the injectors.
That should do it.
F350 diesel cuts off while driving
The problem you have I believe it is the cam sensor.....Low coolant level will cause the same failure ...If coolant isn't touching sensor which is located in the coolant reservoir...when coolant sloshes up and down while driving it will cause this to happen intermittently..Or the coolant sensor is just faulty...If it was fuel related it shouldn't crank at all...The best thing to do is have a dealership scan the system for faults rather than use a cheap scanner."..You can also check to see if there are any recalls....Check wiring for loose connections..also sometimes the negative battery cable will definitely cause this...It will become loose and the vibration will make it happen..and contamination. .".So check battery cables,coolant sensor wiring,and wiring at cam sensor which is located at front of engine behind fan ...If all cables,wiring and coolant level are good take it and have it scanned...Also check oil level...Hope this helps...I would call dealer first and ask about cam sensor recalls..,Then make an appointment..If it is a recall they will take their time and do all money making jobs before yours ...I know because I work at a dealership...They don't make any money for recalls...Good luck...Brooks...
I have an 1999 ford
P0344 = cam position sensor error
P0603 = Internal control module keep alive memory error.
P1670 = communication error between PCM and IDM
P0562 = system voltage low
My guess is you probably have some wiring issues but it's hard to tell exactly where.
Willnot start unless you pull start it
Got fuel? Sounds crazy but you'd be surprised how many times I have poured a gallon of gasoline into someones car to get it to start.
No start condition is the most frustrating problem. More information on what happens when you turn the key would help......but basicaly you need 4 things to make a car start. Fuel. Air. Spark. Timing. Fuel, Air, Spark and Timing are needed to start/run. Asked about fuel, but is the fuel getting to the cylinder? Do you have fuel pressure at the fuel rail(s)? When you turn the key to the "On" or "Run" position, do you hear a whining sound coming from the rear (fuel tank area)? That is your fuel pump priming the system. No sound? Check fuses and relays associated with the fuel system. Air. You need air to the cylinder to make it start and run. Check your air intake and filter. Really clogged and dirty filter? Pull it out and try to start. No go? Put it back (change ASAP) and look for Spark. Spark includes battery. Are there any loose connections to/from your battery? Really corroded terminals? Clean and tighten the connections. Try to start. No go? Pull the spark plug wire off an easily accessible spark plug (grasp the "boot" as close to the plug as possible and wiggle back and forth easily while pulling - these boots and wire connectors are fairly delicate). Remove the spark plug (be careful and dont break it or cross thread it when putting back in) and pop the wire back on it and set the plug on top of your engine (away from the spark plug hole). Have someone try to start the engine. You should see the spark plug fire its tiny bright blue spark. If not, you have found your problem. The problem is likely a bad coil, bad coil wire, distributor cap, rotor or a combination of these. If you have spark, then it has come down to timing. There are lots of things that affect timing in modern cars. There are a couple of sensors that jump out - Crankshaft and Camshaft position sensors. These will generally quit working while driving and you will likely notice the problem beforehand with it running really rough and getting crappy mileage, and the check engine light will come on and give you all kinds of hints. IF you turn the key and nothing happens, it might be a broken timing belt, but again, those usually fail under working conditions. It is possible (rare) the timing belt slipped/broke when you last shut off the engine, but I would point at the other 3 things first (Fuel, Air & Spark). Hope this helps. Good luck.
Speedo not working
It sounds like an electrical problem in wiring?? This would be hard to troubleshoot with out having Hands On. If you are interested in having it checked out and repaired, I would be glad to diagnose it for you, my shop is in Cleveland Al 205-625-5679
Won't start unless pulled
based on the information that you wrote down you have a problem with your ipr injector pressure regulator you need to remove the ipr which is located on the high oil pressure pump on top of the engine for inspection inspect the two orings on ipr if one of the orings is damaged that will be your problem and you will have to replace the ipr orings or ipr if you can't get the oring kit
Solenoid for fisher plow
There are two large terminals One terminal will be just a nut on a bolt and the other will have a wire under the nut that goes down into the starter. The batter wire goes on the one that just has the nut. If you put it on the other one the starter will spin immediately as you are supplying power to the armature direct and by passing the solenoid.
P0607 ERROR CODE
What this means is the PCM has lost some of its programming or there were aftermarket performance parts added to the truck. The electrical values have changed for some reason.The PCM will need to be reflashed. If it drops the instructions agin the PCM will need to be replaced.
Clutch is not completely disengaging
Sounds like you may be low on clutch fluid. Check the reservoir under the hood in the engine compartment and fill if necessary, then you will want to pump the clutch several times to regain hydraulic pressure to the pressure plate. Make sure that the emergency brake is set and that the vehicle is in neutral. You may have a faulty slave cylinder if you have to add fluid to the clutch reservoir. I hope that you have found this information to be useful, and if I can be of any further assistance, please let me know. Thank you for using fixya!
Not finding what you are looking for?