20 Most Recent
2003 Dodge Grand Caravan AWD - Page 9 Questions & Answers
The stud on the Right Front Rotor is turning how
Hi, what you will need to do is take 5 to 6 washers and take the wheel off and put the washers on over the stud that is loose and take a lug nut and tighten it down till it pulls the stud back into the hub. if it does not tighten up and spins you will need to replace it. just take the brake caliper and bracket off and the rotor. then pound the old stud out and insert the new one then use the washers and lug nut to pull the stud into the hub. good luck
Car lighter not functioning
There are two possibilities that has to be checked.
First of all if there is no power at all to the lighter then it can be either the faulty fuse or the fault in the wirings of the cigarette lighter.
The fusebox is under the hood on the driver side. It's about a 10x6 inch black box the fuse mappings are on the underside of the lid.
If both the wirings and fuse checked out ok then its a fault in the lighter itself.
Thanks. you can rate this solution and show your appreciation.
Driver side brake light won't work. Bulbs are new
Pull down the fuse/relay panel under the driver side dash. You will see a fuse for each side of the van> Right brake light and left brake light. Check the fuses for a blown fuse controlling the drivers side and replace it with the same size fuse. Hope this will help you.
Troubleshoot codes
po442 evap system small leak po455 evap system large leak po456 evap system very small leak. the evap system is located under the driverside of van. from all indication you have a hole in a line or a bad connection on one of the lines. inspect and repair.
Engine starts but no electrical items work, ie no
Please look in the power distribution fuse block. There are some large fuses that are either blown or are dirty and need pulled and reseated in the fuse box.
I have had this problem on other vehicles and this issue left me sitting on the side of the road in Ohio one time :)
Check there and get back to me on this issue
How to change ignition lock 2003 dodge grand
Insert the key, tap on it lightly with a rubber hammer while trying to turn it. Remove the cover around the steering colume and once the key is turned to the "run" position, press the small tab on the bottom of the colume and pull the whole cylinder out.
I need to flush the old power steering fluid. How do you do this?
there's alot of machines out to do, the cheap way is to go to local hardware store buy a pump put on drill connect the hose from clean fluid bucket to pump, pump to high pressure line other line in bucket, by-passing p/s pump take about a total of 5 qts to do right, after done connect lines back to p/s pump
My heat wont work it blows cold air
Warm up engine, put your hand on the top radiator hose, is it hot ? can you squeeze it ?
If not, then you should rpalce your thermastat with a 195 degree.
If that does not help you may have a bad head gasket, please let me know.
How do i program 2003 dodge carvan key fob
ATTENTION: You MUST HAVE one working remote to add one more to the system.
If you do not have one working remote right now then these instructions will not work.
You will have to have a Locksmith or dealership use a computer to program the first
remote for you.
Click here to find an Automotive Locksmith in your area to program this remote.
1. Press LOCK button 5 times at 2 second intervals to resynchronize remote.
2. Insert key into the ignition switch. Turn ignition to the RUN position (as far as you can
go without cranking engine). Wait for ignition chimes to stop.
3. Using the working remote, press and hold the UNLOCK button on the remote for 4 to 10
seconds.
4. Within the specified 4 to 10 seconds, continue pressing the UNLOCK button and then
press the PANIC button ( on the programmed remote ) for 1 second and release both
buttons. A chime will sound to indicate that the remote programming mode has been
entered ( allow 3 seconds for chime to sound ).
5. Within 30 seconds of the chime, press and release the LOCK and UNLOCK buttons
simultaneously then press and release just the UNLOCK button on the same remote.
A chime will sound indicating the remote has been programmed. Press and release
the LOCK and UNLOCK buttons simultaneously and then press the UNLOCK button on
each new remote you wish to program at this time. A chime will sound afer each
additional remote is programmed.
6. Turn the ignition OFF and remove key.
7. Test Remotes.
Not finding what you are looking for?