20 Most Recent 1996 Dodge Neon - Page 9 Questions & Answers


The positive battery terminal has a separate heavy wire that goes to the starter. Remove this cable from the battery, clean it and re-install. Just a dirty connection.

1996 Dodge Neon | Answered on Mar 06, 2011


Had similar problem with 97 Plymouth Neon.  It turn out that the Crank Shaft Position Sensor was failing,  since I replaced it the car has been running smooth with no problems.

1996 Dodge Neon | Answered on Mar 06, 2011


change out your fuel pump

1996 Dodge Neon | Answered on Mar 05, 2011


It might be your ac clutch. run your ac if u have it and see if it whines louder.

1996 Dodge Neon | Answered on Mar 03, 2011


When you buy a reman Alt ,you may not get new bearings

You can be rest assured your salvage yard piece is the issue

Put a screw driver on it, and put to your ear

1996 Dodge Neon | Answered on Mar 03, 2011


Were is the horn locate

1996 Dodge Neon | Answered on Feb 21, 2011


Hi, my name is John I will do my best to assist you.

To Remove
  1. Disconnect the negative battery cable.
  2. Disconnect the filtered air tube from the throttle body and air cleaner housing.
  3. For SOHC engines, remove the air cleaner inlet tube.
  4. For SOHC engines, detach the electrical connectors from the engine coolant sensor and the camshaft position sensor.
  5. For DOHC engines, unplug the electrical connector from the camshaft position sensor.
  6. For SOHC engines, remove the brake booster hose and the electrical connectors form the holders on the end of the cylinder head cover.
  7. Unfasten the camshaft position sensor mounting screws, then remove the sensor.
  8. Loosen the screw/bolt attaching the target magnet to the rear of the camshaft.
To Install: NOTE: The target magnet has 2 locating dowels which fit into the machined locating holes in the end of the camshaft.

  1. Install the target magnet in the end of the camshaft. Tighten the retainer to 30 inch lbs. (3.4 Nm).
  2. Install the camshaft position sensor. Tighten the sensor mounting screws to 80 inch lbs. (9 Nm).
  3. For SOHC engines, place the brake booster hose and the electrical harness in the holders on the end of the valve cover.
  4. Attach the electrical connector(s) to the camshaft position sensor and coolant temperature sensor (if necessary).
  5. Install the air cleaner inlet tube and the filtered air tube.
  6. Connect the negative battery cable.
The camshaft position sensor is mounted to the rear of the cylinder head - SOHC engine shown


tecnovative_139.gif
Location of the camshaft position sensor - DOHC engine shown

tecnovative_140.gif

Unfasten the retaining bolt, then remove the target magnet from the rear of the camshaft - SOHC shown, DOHC similar

tecnovative_141.gif

The target magnet has 2 locating dowels for proper alignment during installation

tecnovative_142.gif

1996 Dodge Neon | Answered on Feb 20, 2011


ck see if firing at plugs ck see if has fuel pressure could be timing belt

1996 Dodge Neon | Answered on Feb 08, 2011


Sounds like a dead battery. Lots of times the colder the weather gets, the less "Cranking amps" the battery has to put out.. Try jump starting the car, if that works, check your alternator / battery. (you can get this tested for free at most auto part stores... here in maine atleast..)
If your car is turning over quickly, not doing a clicking sound when your try starting, or a slow start sound, it could be a fuel or electrical issue. I would need more details.. (Mainly if you knew if it was battery related or not.)
Good Luck!

1996 Dodge Neon | Answered on Feb 06, 2011


it is 3/16 and you will go from master cylinder to wheel in Canada $100.00

1996 Dodge Neon | Answered on Feb 01, 2011


There is a "C" clip that holds it in there. Put your pry bar on the fat part of the halfshaft (axle) and give it a few smacks with a hammer. These jolts should knock it loose to be able to remove it. If you cant get room to hit it with a hammer you will have to use a pry bar and just keep working at it on both sides.

1996 Dodge Neon | Answered on Jan 15, 2011


1995 neon wont find a gear is a5 speed with 2.0L just stoped no warning sing or noise checked cluch cabel and shift linkage

1996 Dodge Neon | Answered on Jan 06, 2011


Hi

the most likely cause of this code is the MAF sensor or air mass sensor "same thing" this regulates the air to fuel mixture, worth a mention you can try and clean this sensor with carb cleaner and this often cures the fault.

Regards
Dan

1996 Dodge Neon | Answered on Jan 02, 2011


it sounds like you have a leaking heater core it either is bad or you have a leak where the hoses attach to the heater core. if the water doesnt have antifreeze in it then maybe your window seal is leaking. hope this helps you . best of luck. have a nice day.

1996 Dodge Neon | Answered on Dec 28, 2010


Hello toasty_17 and thank you for asking your question, on Fixya.

Here is a simple process that will walk you through a few steps that will pinpoint the overheating problem on your 1996 Dodge Neon, without even using any tools. It has helped millions of people, and I am certain that it will help you, because I wrote it for people like you. So here is the link:
How to diagnose your overheating Neon

Get more great, money saving, tips and tricks about your vehicle from: twitter.com/acoates23234

Thanks for the vote, and good luck!

1996 Dodge Neon | Answered on Dec 27, 2010


if it is the trans pan is what you are talking about then it is sealed by rtv silicone but you should check if it is the cooler lines leaking down to the pan and looking like the pan there is also a solenoid pack on some vehicles that leaks down as well.

1996 Dodge Neon | Answered on Dec 15, 2010


It is located on the left end of the cylinder head, next to and in front of the CMP sensor. There is no easy way to access this sensor. The Haynes Manual says to remove the CMP sensor to access this. To remove it with a socket you have to remove the battery and battery tray. When you put the new sensor in make sure you wrap the threads with Teflon Tape to help prevent leaks.

1996 Dodge Neon | Answered on Dec 13, 2010


It is located passenger rear right where you right foot would be sitting in back seat but under neath car it is held by a 10mm bolt or 3/8 inch.

1996 Dodge Neon | Answered on Dec 13, 2010

Not finding what you are looking for?
1996 Dodge Neon Logo

534 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

2002 Dodge Neon
2002 Dodge Neon

839 Questions

2004 Dodge Neon
2004 Dodge Neon

733 Questions

2003 Dodge Neon
2003 Dodge Neon

727 Questions

2005 Dodge Neon
2005 Dodge Neon

688 Questions

2000 Dodge Neon
2000 Dodge Neon

598 Questions

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Neon Dodge

  • Neon Dodge

Most Popular Question

turn signals brake lights quit working

  • Cars & Trucks
Loading...