20 Most Recent 2001 Pontiac Montana - Page 2 Questions & Answers

check for bad ground wire connections

Make sure battery has a full charge and battery connections all good. Check fusible links where applicable. Pick any component that is fuse protected and doesn't work. At the fuse box, check that fuse circuit for voltage, use a test lite. Even if the fuse is good, if no voltage on the fuse circuit, the circuit is still dead. Some fuses are hot all the time, some go hot with the key on. Do any electricals work?

Spark plugs, plug wires, oil filter and 5 quarts of oil.

It could be a timing issue (misfire) but it absolutely could also be either air or fuel filter. If it's starving for fuel, it's the fuel filter. If it's starving for air (too rich), it would also stall out and that could be the air filter. Basically, you need 4 things to make an engine work: compression, air, fuel, and spark.

Communication network error code ! Class 2 serial data ! All the modules on your vehicle share information on this network . Buick Class 2 Operation Diagnosis 1998 Pontiac is the same !

STARTER REPLACEMENT (ENGINE ELECTRICAL) Document ID# 688149 Starter Replacement

Removal Procedure

Important: This vehicle uses the PG260 F1 starter motor. The starter motor is serviced only as a complete unit.

1. Disconnect the battery ground (negative) cable from the battery. Refer to Battery Negative Cable Disconnection and Connection.
2. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
3. Remove the starter motor BAT terminal nut and electrical leads.
4. Remove the starter motor S terminal nut and electrical lead.
5. Remove the torque converter cover. Refer to Torque Converter Cover Replacement in Automatic Transaxle - 4T65-E.
6. Remove the starter motor bolts.
7. Remove the starter motor.

Installation Procedure

1. Install the starter motor.
Notice: Refer to Fastener Notice in Cautions and Notices.
2. Install the starter motor bolts.Tighten: Tighten the starter motor bolts to 47 [n-m] (35 lb ft).
3. Install the torque converter cover. Refer to Torque Converter Cover Replacement in Automatic Transaxle - 4T65-E.
4. Install the starter motor S terminal electrical lead and nut. Tighten: Tighten the starter motor solenoid S terminal nut to 3 [n-m] (27 lb in).
5. Install the starter motor BAT terminal electrical leads and nut. Tighten: Tighten the starter motor solenoid BAT terminal nut to 10 [n-m] (89 lb in).
6. Lower the vehicle.
7. Install the battery ground (negative) cable to the battery. Refer to Battery Negative Cable Disconnection and Connection.

Try emergency flashers...if they work then may be fuse??/

First thing is to check the fuses

number 143/75 30amp; fuse box is on the right side of the cockpit open the front passenger door and you will see the cover of it

Once you have all the pan bolts out, remove the bolts on the front two motor mounts. Use a floor jack and a piece of wood on the crankshaft pulley to raise the engine just enough to clear the suspension and steering components.

If engine cranks but diesnt staet then Most likely fuel pump / fuel filter has a problem.

Hi there I am technology tech mechanic I work on electric and man. I come from line line of mechanics I am 5gen OK to start how are you wanting some one to help you if you are not going to have more information then you give I don't know any body can help you with what you gave me to work with!!! Let me ask you this how many kinds of cars are there? Bunch of them so how are you expect to get help with that!!! So come on now pull out ur head and think a min or I promise you no one going to no!!! I am a professional mechanic and I cant no where or what window and the car

Turn Signal Lamps The turn signal lamps may only be activated with the ignition switch in RUN or BULB TEST position. The T/SIG fuse supplies ignition voltage to the turn signal switch. When the turn signal switch is placed in either the left or right position, the turn signal switch sends an ignition voltage to the hazard lamp/turn signal flasher, which sends an on-off signal to the turn signal switch. When the turn signal switch receives the on-off signal it will send that signal to the following lamps on the LH or RH side: ?€¢ The Rear Turn Lamp

?€¢ The Turn Signal Indicator

?€¢ The Sidemarker Lamp

?€¢ The Sideview Mirror (Pontiac Thunder only)

The turn signal switch also sends a separate on-off signal to the Daytime Running Lamps (DRL) control module, which relays the signal to the appropriate front turn signal. The front turn signals are grounded at G101 and G102. The rear turn signals are grounded at G401. The sidemarker lamps are grounded through the corresponding front parklamp. The sideview mirror turn signals are a bank of LEDs placed behind the mirror glass. The hazard lamps operate on battery voltage. The HAZARD fuse supplies battery voltage to the turn signal switch. When the hazard switch is pressed, the turn signal switch sends battery voltage to the hazard lamp/turn signal flasher, which sends an on-off signal to the turn signal switch. The turn signal switch send the on-off signal to all the turn signal lamps, causing all the lamps to flash including both IPC turn signal indicators. The hazard lamp/turn signal flasher is grounded at G200. When the parklamps are ON, the sidemarker lamps receive voltage from the park lamp supply voltage circuit and illuminate. The sidemarker lamp is grounded through the corresponding rear turn signal. When the turn signal switch is place in the left or right hand position, the rear turn signal illuminates and the sidemarker lamp will loose its ground, causing the sidemarker lamp to turn off when the turn signals are on and to illuminate again when the turn signal is off. Which blub an socket did you replace ? check the other blub ? The switch and or the flasher module can cause this problem . Replace the turn signal switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering Wheel and Column. Did you complete the replacement? Which

images for 2001 Pontiac Montana rear springs ..

Replace broken rear coil spring on pontiac montana - Fixya

www.fixya.com/cars/t3213136-replace_broken_rear_coil_spring_pontiac Oct 17, 2009 - replace broken rear coil spring on pontiac montana - Pontiac 2000 ...Im having problems with my rear lighs on my 2001 pontiac montana, the ...

Behind rear hatch plastic follow house find rubber grommet and house running to overfow cater

sending unit or float in gas tank, check if any broken wires or well plugged in and then check the float for the gas.

Hi there : what year make and model, how long do you drive before it stalls? And how long before it starts