Top 20 1994 Mazda 626 Questions & Answers

0helpful
1answer

Mazda 626 fs 2.0l Starts Idles revs up clean but

look at your fuel filter
2/23/2018 6:39:03 PM • 1994 Mazda 626 • 346 views • 0 helpful votes
0helpful
2answers

Mazda 1994 626 - OBD-1 Checkup?

There may be some codes in memory that a code reader can reveal.
8/16/2017 1:18:03 PM • 1994 Mazda 626 • 133 views • 0 helpful votes
0helpful
1answer

Car stalls while driving at high speeds

i would start by checking the spark plugs and leads. if that ok i would think there is a problem with the dispack that the spark plug leads fit to, if its cracked or any rust i would replace.
5/23/2017 4:39:03 AM • 1994 Mazda 626 • 203 views • 0 helpful votes
1helpful
1answer

94 Mazda 626, 2.0 standard. firing order 1342. I know 1 goes to 1. Does # 2 cylinder go to number 3 on the cap and # 3 cylinder go to number 4 on the cap and # 4 cylinder go to # 2 on cap I'm at TDC

The order is as described, but you must know whether the rotor button turns clockwise or count clock wise as this may reverse the position order of the wires to the distributor cap. With the distributor off crank the engine and observe the direction the rotor turns.
10/11/2016 4:35:54 PM • 1994 Mazda 626 • 217 views • 1 helpful votes
1helpful
1answer

Where is inertia switch in 94 Mazda 626 2.0

No inertia switch. That was a common problem on these cars., The alarm box gave problems and it is what is causing the fuel pump to shut off. Good luck finding one. The easiest and cheapest way to fix is to give it ignition power when you turn ignition on. If you want to be a bit safer, buy a ford KA inertia switch, secure it at the l/f kick panel directly onto the body (It works with shock waves) to cut of fuel in case of an accident Luckily you don't have to take the tank out, you just remove the rear seat and the metallic cover. .
7/27/2014 6:56:55 PM • 1994 Mazda 626 • 876 views • 1 helpful votes
0helpful
1answer

Is there a reset button for a fuel pump 94 Mazda 626

Here you go, it should be to the left of your left foot wile sitting in the driver's seat under a panel.
7/23/2014 9:05:24 PM • 1994 Mazda 626 • 496 views • 0 helpful votes
0helpful
1answer

Where is inertia switch i

Here is a video.
7/27/2014 6:43:36 PM • 1994 Mazda 626 • 221 views • 0 helpful votes
0helpful
1answer

Location inertia switch

Here you go.
7/27/2014 6:26:40 PM • 1994 Mazda 626 • 171 views • 0 helpful votes
0helpful
1answer

Is there a reset inertia button for a fuel pmp 94 Mazda 626 2.0?

Here is the video.
7/27/2014 3:50:36 AM • 1994 Mazda 626 • 165 views • 0 helpful votes
0helpful
1answer

Is there a reset button for a fuel pmp 94 Mazda 626

yes, take the negative and positive cables off the battery and put both CABLES together for 30 seconds then re hook both cables properly back to the battery, start car and let it relearn idle for about 15 mins. what exactly is the problem? I’m happy to assist further over the phone at https://www.6ya.com/expert/josh_8f8ad0a8f7e0e6d3
7/27/2014 3:56:43 AM • 1994 Mazda 626 • 121 views • 0 helpful votes
0helpful
1answer

Will not start replaced distributor and starter and it's getting fuel

Sounds like you slipped a gear tooth on the distributor or sheared the pin. Check the timing with a timing light. Bet you are off some 25 degrees.
3/24/2014 6:54:07 PM • 1994 Mazda 626 • 70 views • 0 helpful votes
0helpful
1answer

Need to remove locking wheel bolt on my 1996

If you do not have the original lock key for the wheel bolt, you can always take a socket and tap it on to the wheel bolt (it should fit tight) and then use a ratchet to remove the socket and in doing so, you will remove the wheel bolt as well. Good luck
8/21/2013 11:51:10 AM • 1994 Mazda 626 • 61 views • 0 helpful votes
0helpful
1answer

Wont start

I would check the fuel level first
7/2/2013 11:09:03 PM • 1994 Mazda 626 • 57 views • 0 helpful votes
0helpful
1answer

Location of the fuel filter

Should be in the engine compartment between the engine and the firewall.
6/25/2013 2:43:15 PM • 1994 Mazda 626 • 28 views • 0 helpful votes
0helpful
1answer

Coil seems to have no output

sounds like the immobilisor but? best advice i can give without having my head under the bonnet is to ask a local mechanic to have a look for you
4/14/2013 8:46:25 PM • 1994 Mazda 626 • 38 views • 0 helpful votes
0helpful
1answer

How do i change the timing belt?

You have to disassemble the front of the engine.First thing you need is a book.
4/15/2013 9:32:20 PM • 1994 Mazda 626 • 28 views • 0 helpful votes
0helpful
1answer

I cant find where to hook up the ground wire there are three batt. hook ups on it not sure why! does it hook to the frame ? and is it the long one or short one ?

Usually the long heavy cable goes from the negative post to the engine, and the smaller ground wire goes to the body or frame.
3/2/2013 7:49:33 PM • 1994 Mazda 626 • 60 views • 0 helpful votes
0helpful
1answer

Water pump

water pumpthat is some question
1/24/2013 6:24:28 PM • 1994 Mazda 626 • 23 views • 0 helpful votes
0helpful
1answer

Not passing DEQ

To much fuel not enough air. Find out where the restriction is at.
11/26/2012 9:02:27 PM • 1994 Mazda 626 • 60 views • 0 helpful votes
Not finding what you are looking for?
1994 Mazda 626 Logo

302 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

1999 Mazda 626
1999 Mazda 626

544 Questions

2000 Mazda 626
2000 Mazda 626

410 Questions

1998 Mazda 626
1998 Mazda 626

356 Questions

1995 Mazda 626
1995 Mazda 626

269 Questions

1997 Mazda 626
1997 Mazda 626

277 Questions

Top Mazda Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

626 Mazda

  • 626 Mazda

Most Popular Question

inertia switch in 94 mazda 626 2 0

  • Cars & Trucks
Loading...